hulk 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

The left adapter does require a small alteration which I did with a pair of side cutters (the ones that came with my Ender 3) (see pictures): - Unscrew the four screws at the bottom (be careful these strip easily) - Gently pull back the white tabs...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

Printer Settings: * Printer Brand: RepRap * Printer Model: Original Prusa i3 * Rafts: No * Supports: No * Resolution: 0.2mm * Infill Percentage: 25% Print Notes: I utilized a 0.8mm nozzle to expedite the printing process, which took approximately...

Most LEDLB, LEDP10W and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. ...high/low beam,...

Description ==================== The display is mostly based on Modeller's 1/64 Initial D display box but I have expanded and slightly upscale the width of the roads to fit Hot Wheels better. The holes for tying the cars are designed to fit most...

It does not matter which direction is taken.Continue running the line down and up between the pieces through different holes until it is fully connected.The line must turn a corner on the bottom piece, so ensure that it is placed completely in the...

It may also have fitment issues with non-TM branded or aftermarket upgraded models. Please read the Print Settings section for details. ==CONCEPT== The JTW HCC-2A is the evolution of the Hi-CAPA Carbine Version 1...

Currently, there are three models:Ebook Reader Holder (1x3):This was designed for my Kindle Oasis in its third-party case (if you want it for something thicker than ~15mm, let me know and I'll see about whipping you up a variation)1x3 footprint on...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons? Feel free to remix it as you wish. It would be nice if you upload the remix...

This print allows to elegantly mount your Bosch eBike Charger to the wall, out of the way, right where you need it. I made this version because several people indicated that they liked my eBike Charging Station but preferred a standalone version of...

Which means planning so the bridges will look nice enough/not stand out too much.This also means some very precise modeling so that the slicer can handle a bridged over area with a hole in the middle. Here, I build up to it layer by layer with...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening] The last child of Minera to rise from the ocean depths as a great landmass. Tharador is the smallest of all continents and most meager...

 The fan mounting holes are sized to accommodate a Brass Heat-set insert size M3x4mm.  The holes are not threaded and too large to accommodate an M3 screw itself.   Upgrading the Raise3d Pro2 with a Copperhead  Note: Both Hotends must be replaced...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

The previous file had a gap of 1 mm in the height of the wall between the two cutouts at the front of the model. The replacement file fixes this. Updated "Ability Card Divider" file, to include a cut-out, to make lifting deck from the tray easier. I...

Found a simple hip flask just laying about USHip flask discovered seemingly abandoned USHip flask uncovered, left behind USHip flask in basic design chanced upon USHip flask, a basic model, was stumbled upon USHip flask, plainly designed, was located...

You can find the newer version here: Phone Mount for Van Moof S2/S3 V2.0==================================================================== Rotating Phone Mount for the Van Moof S2/S3 electric bike.Mounts to the handlebar using 3 cable-ties,...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

Before you merge them, DUPLICATE the logo "hole" model (Ctrl D) do not use copy paste it will "shift" duplicate will keep it where it is. Now shift select the body and merge to make your hole cut. You will note you still have the duplicate hole. Now...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

this model the reason I like it better is because it locks into place then you just press the button and it works so nicer better than the others hear that you just hold it in with pressure. Arduino program settings this is all new to me I...

... diameter of the hose end 30mm away from the tip (the wider part) This will give me the diameter and taper needed to revolve a new part for anyone who wants one. Please let me know what make/model it goes to and I'll add it if I am able. ...

I made a slight modification to the model by changing the profile of the USB input so the bridge was less than 5mm (was almost 10mm) and changed the way the board mounts so the top has all socket heads and no washers (just an aesthetic thing). <a...

The bowl model is a solid piece, and CAN be printed in vase mode / spiralize outer contour. This, however, isn’t the strongest. What I do is print them with 0% infill, 2-3 outer walls, 4 bottom layers, and 0 top layers. Basically makes it a double...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp...