i3 cable 3d models

this unit for prusa i3 cable organize. I made 2 different part for cable holder. ...One of middle and one of left side.

attachment for i3 cable ducts, allows for neat wiring to the X and Z carriages, with single axis cable chain motion for all wiring Instructions Check out my YouTube Channel at https://www.youtube.com/user/JBFromOZ Print, attach, wire up enjoy a...

AnyCubic Mega I3 Cable Nozle

This is a Cable Guide for the Anycubic I3 Extruder.

Cable holder for Prusa I3 3d printer which prevent cable connected to hotend tumble down printed model or printed supports from bed and prevent tangle this cable with other cables.http://a360.co/2fVmVtH

This is a cable guide for the x-axis and hotend cables on a Hictop i3 3D printer. The cable guide mounts to the x-carriage using the existing M4 screws. ... Groves along the side allow for zip ties to provide strain relief for the cables.

On my Monoprice Maker Select IIP (Wanhao i3) the bed heater cable would snag on a metal tab on the base as the print bed moved back and forth. This part slips over the tab and provides a smooth sloped surface for the cable to slide over - preventing...

A complete cable management system for the HIC Reprap Prusa i3 I used the cable chain from here: http://www.thingiverse.com/thing:709568 for the chain and also edited a little bit the PSU end stops to use in this design. ... I also edited the inline...

... Lastly this is still work on progress since I'm still working to modify the rear cable conduit to move the wires at the center. If you like the thing please share with us. Print Settings Printer: Wanhao Duplicator i3 v2.1 Rafts: No Supports: No

2 parts clip on cable guidance for 6 mm frame with connecting hooks for zip tie.

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=554725 Instructions Using the following options: cable_width = 1 cable_holder_thickness = 3 number_of_teeth = 6 tooth_depth = 1 number_of_holders = 6 holder_spacing = 10

Needed something to guide the cable from the RAMPS board to the extruder. Designed a simple holder that can be attached to the backside of the upper left Z-axis holder. You might have to replace your (2) M3 bolts by others that are 5mm longer. ... ...

Wanhao Duplicator i3 cable grommet to protect the wires that run under the rear rail next to the Y-axis stepper motor. To install, remove the zip tie holding the existing wires in place, move down and slide grommet into place. ...Install a new zip tie...

This DIY Prusa i3 cable management part was designed to provide a way to clamp and zip tie to keep all the wiring clean. The Ramps board was installed towards the bottom of the frame. The cable management part is meant to screw into the original...

Remix from the following: Top Mount - Geeetech Prusa i3 Pro - Cable Chain Top Mount by Piggei Chain Ends - Geeetech Aluminium Y Axis Cable Chain by Bernbout Extruder End Mounts - Geeetech Prusa i3 - Cable Chain Mounts remix by Babokaj CURRENTLY...

A simple mount for the main cables on the Sunhokey Prusa i3 printer. ... You can use the M3 screws and nuts that came with the printer.

A simple cable guide for the heatbed wires on a Wanhao Duplicator i3. Snaps on to the back of the printer and uses a zip tie to hold the cables down. ...Easy & fast print.

A simple cable guide for the heatbed wires on a Wanhao Duplicator i3. Snaps on to the back of the printer and uses a zip tie to hold the cables down. ...Easy &amp; fast print.</p> Category: 3D Printer Accessories

Cable Chain Management parts for the Prusa i3 : These are mostly re-works or improvements made on some things found & adapted for the Prusa i3 & as such are a work in progress. Revised & strengthened version of Chain Link by bqLabs : +...

Moves the cable chain mount a little bit backwards. ...Suppose to be mountet on the X axis

There are 2 heights of cable ducts included, I've only used the "short" ones which fit a stock MK2S without feet, the "tall" ones I haven't printed/tried but allow for additional cables beyond originally included, they just need to be rotated to the...

... Print Settings Printer: HICTOP Prusa I3 Rafts: No Supports: Yes Resolution: 0.15 Layer Height Infill: 20% Notes: Printed with support "Touching Buildplate" with the rectangular cut out facing the bed. ...How I Designed This Modeled in Solidworks.

If you imagine it coming straight up flat against the frame, twist it counterclockwise around a half turn which basically causes it to roll over to the front exiting to the right with the other wires.Bill Of Materials: The parts below are required...

I loved the thought of cleaning up the cables and adding a personal touch to your 3d printer to make it more your own so I removed the wanhao rhino and have made it blank to allow for your own personal logo or any other design you might want to...

they clip 'yer wires to 'yer rails...

<p>Reupload of <a href="https://www.thingiverse.com/thing:1218943/">https://www.thingiverse.com/thing:1218943/</a> as it has been removed from thingiverse. ...I am not the original author</p><p>Credit to: <a...

SummaryHad problems with the wires to nozzlen hang down and lie against Beden. ...So I had the idea to draw a small console to the cords.Print SettingsPrinter Brand: RepRapPrinter: Prusa i3Rafts: Doesn't MatterSupports: YesInfill: 20%Notes: Support...

First off this is totally cosmetic and will not make your prints any better. With the extruder stepper motor rotated and the wires behind this I can get the full 180mm Z-height (see picture) even with LED lights installed under the top of my gantry.

... wise you may or may not need a support. Post-Printing Right Bracket Left Bracket Cable Routing Cable Routing Cable Routing Cable Routing & Extruder cable tie-wrap. ... Bracket with spacer for washer and nuts.

Anycubic i3 mega cable mount Never break a cable again! ... With or without cable tie .