icom a4 battery 3d models
75976 3d models found related to icom a4 battery.thingiverse
Recently a my friend broke the plug to recharge his radio and asked me to fix the problem. After verifying the irreparable nature of the radio I decided to buy a cradle on the internet but I do not find any. So I designed and printed this thing. ...
thingiverse
Blank insert for Icom IC-705 for if you don't want the back open, while running on external power without a battery inserted.
thingiverse
Icom BP-272 Battery Protector Case The battery stay in place when using the belt clip.
thingiverse
Battery compartments for ICOM IC-E90 (FM transceiver). Combined with standard rechargeble batteries these replace the original battery packs BP-216 / BP-217. Requires that you make the contacts (e.g. from a tin can) and glue / solder them into the...
thingiverse
Needs battery-management, step-down converter 5A. 13V output (adjustable), with small cable to DC-in, see pictures. Also a preotection-circuit is needed to protect transceiver against high voltage (16,6V) in case of damage of the DC-DC converter. ...I...
thingiverse
4 x Printed Bushings STL 2 x Printed Locks STL 2 x Printed Pins STL 1 x Printed 705-Battery-Pi STL 4 x M2.5 x 16mm Screws to mount the pi. 2 x Springs 11mm long and 4mm diam for Locks, I used a spring from an old ink Pen. Screws to mount the Pi...
thingiverse
To date it is physically correct: 1) the adapter slides easily on the base of my radio, 2) the retention tab clicks in place 3) there is enough clearance for the electrical contacts The external shape is a bit bigger than the radio, to be perfect...
myminifactory
Battery cover for ilife a4 remote control If you find my models useful, please consider tipping. ...It helps me to allocate more time for making models.
thingiverse
In order to use 3xAAA batteries, you need the spacer, as it presses down on the PCB thru a whole, likely in order to tell the iCOM to have a different voltage, Place this spacer in our iCOM and then insert the batteries and all should be good. ... You...
thingiverse
NiCD battery performance is disappointing so I decided to design my own BP-173 compatible battery pack with two 18650s inside, providing 7-8 volts for Icom W32E (and other BP173/BP180 radios). 1. Print all parts, 0.2 mm layer, 3 walls, supports...
thingiverse
In case you need to put nickel or alkaline batteries on your icom receiver, you will see that it does not turn on. This is because there some taps that make some contacts in order to let the batteries power the unit. The original design has some...
thingiverse
... you might have to adjust. Note: This is not an official ICOM part, has not been authorized by ICOM in any way, and this part has been created without copying a genuine AD-99N (I do not have one). ...Icom and the Icom logo are registered trademarks.
cults3d
There was a problem with the original stl file (mesh problem) that i have fixed.
thingiverse
There was a problem with the original stl file (mesh problem) that i have fixed.
thingiverse
Bracket to mount the Icom 2730A onto my desk. Desktop thickness is about 16mm. There are 4 parts to this design. -The base, which is ziptied to a bar underneath the desk. -The arm, lifts the faceplate up and angles it. -The backplate, which...
thingiverse
I found that I was wasting photo paper as I had A4 size photo paper with me and the photo frame for that size is not only too larger to print but also not aesthetic. On the other hand photo frame, 4 inches by 6 inches was too small, and more...
thingiverse
Soporte Icom MB-63 para Icom IC-706MKIIG. ...Icom MB-63 holder to fits with Icom IC-706MKIIG.