icom id 4100 3d models
1073782 3d models found related to icom id 4100.thingiverse
Mount for Icom ID-4100. v1 - It works so unless I find some flaws as I use it I don't suspect I'll revise it. There is about 1mm gap from the radio on each side. Using 4 m4x8 screws I was able to cleanly attach the radio. There are 4 mounting...
thingiverse
ICOM ID-4100 Head Bracket V1 ============================ After the original bracket broke, I decided to do my own thing. ICOM is nice, but the proprietary mounting method isn't fantastic. As such, here is a bracket which will accommodate your own...
thingiverse
This is a set of brackets to hang an Icom ID-4100 VHF/UHF/DSTAR Mobile Radio and Icom SP-35 Mobile Speaker. They are designed so the speaker and radio front are close to the same plane when mounted. Icom no longer includes the MBF-4 mounting...
thingiverse
Holder for ID-51 to be placed on the table. Can also be permanently installed. ... Using with any PLA
thingiverse
Piece to bolt onto the included magnetic mount with the Icom ID-5100 and connect to 1" RAM mounting hardware
thingiverse
A simple stand to support the Icom ID-51 . ...cut outs allow access to the charge ports etc.....
thingiverse
... magnets/plate to be installed on the back of the faceplate. There is a finger groove for leverage against the touch screen so it doesn't slide around when you're operating it. (tags) Icom ID-5100a 5100 ID5100 HAM amateur Radio ICOM Yaesu Kenwood
thingiverse
This is a ICOM ID-5100 display stand that connects to the radio's main body through the original lateral screw. ...Print Settings Printer: ZORTRAX M200 ...
thingiverse
This is a RAM Mount compatible holder for an iCOM ID-51. It will fit the larger battery as well as the stock battery. I used M4X25's to put it together. There is a tiny amount of space for thin rubber cushion to keep it from rattling. If it will stay...
thingiverse
I wanted a simple and quick to print desktop stand for the Icom ID-5100 front panel. I'm planning on using the radio in a couple of vehicles so I'll be moving it around. The stands and the front panel don't weigh much so if you set it up in front of...
thingiverse
Underside mount for ID-880H remote head. ...Designed in two parts that are easily glued together for ease of printing.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=81117 Instructions Using the following options: to_angle = 340 wall_thickness = 4 sa_height = 70 to_length = 28 sv_angle = 65 tv_length = 12 base_length = 80 sa_angle = 110 fuzz = 0.1 sv_height...
thingiverse
This is a display stand for the Icom ID-5100. This stand can be installed on the radio or it can be used on the desk. The display can be attached directly with the two rear screws or it can be attached with the MBA-2 kit with the moguls to be able...
thingiverse
May 2020 From Randy - W4LKS ICOM ID-51 3D Printed Desktop Stand Here is a simple desktop stand that holds the ID-51 at a pleasant angle for viewing the screen while it sits on your desk. The base is wide enough so it would be hard for an earthquake...
thingiverse
ICOM doesn't make anything for the that so I did. This is uses a counterbored bolt in the center for the Lido mount. ... http://www.lidomounts.com/homepage.html Instructions Print in ABS or it will...
thingiverse
This is a quick and dirty stand to allow you to keep the ID-5100A head unit vertically mounted on a desk. It's not locked into the stand, so its free to move around, but there is a cutout for ventilation that needs to line up with the vents on one...
thingiverse
I had an old cellphone mount still in my truck - and thought a printed baseplate could turn it into a great place to mount my ID-800H's tuning head. Instructions I printed this with PLA and 25%...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/0dGnhblBPDL
prusaprinters
For some time, I'd used a pair of zip ties to keep the SP-35 speaker attached to the suction cup mount for the Icom ID-5100 controller head, but this 3d printed bracket is a sturdier (and tidier!) solution.You will need:The Icom ID-5100 (may worth...
thingiverse
This is a simple wedge-shaped stand for the ICOM ID-4100A dual-band mobile radio. It is designed to lift the radio off a desk and make the screen/buttons more accessible. Given the relatively-close dimensions of the older ICOM IC-880H, it should...
cults3d
This is a simple wedge-shaped stand for the ICOM ID-4100A dual-band mobile radio. It is designed to lift the radio off a desk and make the screen/buttons more accessible. Given the relatively-close dimensions of the older ICOM IC-880H, it should...
prusaprinters
This is a simple wedge-shaped stand for the ICOM ID-4100A dual-band mobile radio. It is designed to lift the radio off a desk and make the screen/buttons more accessible. Given the relatively-close dimensions of the older ICOM IC-880H, it should work...
thingiverse
Dies ist ein Ständer um das RX/TX-Modul senkrecht stellen zu können. Zur Montage im Kofferraum musste ich den Sendeblock höher haben um einen möglichen Wasserschaden durch eindringendes Wasser vorzubeugen. Macht sich aber im Shack auch ganz gut um...
thingiverse
A ham friend and I were talking about the need for a ptt stopper. ... Tinkercad and here it is.
thingiverse
I had a problem. I'm a ham operator, and had no place to mount my radio head unit in my new Dodge Journey. Well.... 3D printing to the rescue! This set of dovetails is mounted in the top of my Dodge Journey's cubby hole, with the 4.3in Uconnect...
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4uRJPeqA6ub
thingiverse
Dies ist ein Ständer um das RX/TX-Modul senkrecht stellen zu können. Zur Montage im Kofferraum musste ich den Sendeblock höher haben um einen möglichen Wasserschaden durch eindringendes Wasser vorzubeugen. Macht sich aber im Shack auch ganz gut um...