igloo cooler latch replacement 3d models
158914 3d models found related to igloo cooler latch replacement.thingiverse
Replacement latch for old style igloo cooler latch I could not find the old style latch for my igloo cooler, so I designed these plates to go where the old latch had been. The cooler lid already closes tight enough with friction, so I made a plate...
thingiverse
Print Settings Rafts: Doesn't Matter Supports: Yes Resolution: .2mm Infill: 30% Notes: The latch portion prints 2 mm above the bed so it needs to be supported. I used a 10% support in Simplify 3D software. I used Taulman's Nylon "Alloy 910" to...
grabcad
Replacement insert for the older style Igloo Coolers with a latch and knob cover.Printed on a Stratasys Fortus 450 with Nylon 12
thingiverse
A replacement latch for a Igloo MaxCold cooler. Update (10/14): Reinforced hinge to prevent breaking. Instructions Print and use large paper clip as axle to hold parts together. ...Paper clip should...
thingiverse
This is a repair part for the Playmate line of coolers, it is the latch that holds the lid closed. This part is not available from Igloo so I had to make one to save my trusty cooler from the dumps! Please leave a comment if you use it. ...Enjoy!
thingiverse
This is a latch I designed for an Igloo Cooler with a 2" bolt spacing. This will only work with some type of flexible filament such as TPU. ... I purposely designed it to be very snug assuming it would loosen up over time.
prusaprinters
I got tired of buying the plastic latches for my Igloo cooler that I enjoy otherwise so I designed one to be printed in TPU and outlast all the bending. Version 1 was a quick quick model to get me out the door the next day for our trip. ...Version...
thingiverse
The latch on my igloo cooler broke, so I designed a new one. Instructions: Print 2 of the "rod half" files and then glue them together with some super glue. The rod will be very tight in the main latch, so to take care of that and any...
thingiverse
This is a replacement hinge for many igloo coolers that use a flexible plastic hinge. Print this in a flexible filament such as TPU and ensure the hinge flexing section is completely solid all the way through. ...The holes are spaced 44mm apart width...
thingiverse
This is a replacement hinge for a large Igloo cooler. This parts prints in place and does not need to be assembled. You may need to use a pliers to get the movement working initially. ... Fusion 360 project file: https://a360.co/2z9QsxV
thingiverse
Igloo Replacement Cooler Hinges! Instructions Print out 2 of these. I used a .180" diameter hypotube (McMaster PN 8988K443) cut down to length. It's what I had lying around... Turn one of the...
thingiverse
Igloo cooler latch with hook at the bottom, remixed from dadam_k's excellent work. ... Nearly identical to their work but includes the small hook shape at the bottom of the latch for interfacing with the cooler.
thingiverse
Remix of the Igloo MaxCold Cooler Latch. The difference is this is a hinged latch that does not require a pin to assemble. No assembly required.The pin is modeled into the latch. Both parts of the latch print together and the hinge is functional...
pinshape
Latch on cooler broke so I made a new one. Printed with Taz 5 with FlexyDually printhead, Uses 1 meter of NinjaFlex and 4 Meters of ABS. "Everywhere support" setting required. Takes about 3.5 hours to print. I overlapped the NinjaFlex and ABS models...
thingiverse
... part for the Igloo Paymate Elite. ...When the cooler no longer locks its because an internal latch is broken. It's easily replaceable. ...This part is modeled in Solidworks and the part is improved for strength to be printed in PLA or ASA.
thingiverse
One fateful day I noticed that the lid on my Igloo 'Little Playmate' cooler no longer latched closed. Alas, the piece inside the lid had broken. I designed this replacement in Fusion 360 after measuring the piece that was remaining under the lid...
thingiverse
Replacement for my Igloo 5 gallon sport water cooler that broke. This was my first 3d cad project, but turned out great even if it did take 8 hours to figure out how to design with all the curves and angles. ...
thingiverse
The title says it all. ... A replacement latch for your old broken down cooler. ... Print and attach to your cooler.
cults3d
The title says it all. ... A replacement latch for your old broken down cooler. ... Print and attach to your cooler.
thingiverse
Replacement hinge for Igloo coolers designed to be printed out of flexible/semiflex material like TPU. ... Mounting Holes: 46 mm x 16 mm
thingiverse
It is a "print in place" hinge made to replace broken hinge on Igloo brand cooler. It has two additional screw holes (total of 6 per hinge) just in case you want to add a little more reinforcement. Stardard print: I used PLA at standard...
thingiverse
Requires reusing the pin from the existing broken latch which is 0.42mm diamater and 45.20mm length if you need to buy/make a new one. Should be fine making a plastic pin if needed as it doesn't have many forces acting on it. ... ...
thingiverse
Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.
myminifactory
The Hardware requirements are: - 2x hex nut - 2x round or socket head bolt between 3/4"-1" (20mm-25mm) To complete the assembly the following parts are required: - 2x Igloo cooler handle arms - 1x Igloo cooler handle mount - 1x Igloo Cooler handle in...
thingiverse
Igloo replacement cooler Button. Almost everyone i know has a small little igloo cooler and at some point someone (maybe a kid) Opens it to far and the button pops across the room and disappears forever. Well now you don't have to throw it away and...
thingiverse
replacement hinge for igloo coolers. print in a flexible pla material. i used ecoflex pla and worked perfect. something like semiflex or esun flexible would work as well. ...a soft nylon like bridge might work nice also
thingiverse
This design has been moved to printables.com https://www.printables.com/model/154208-igloo-cooler-handle
cults3d
Mini Igloo Playmate cooler. ... This is a novelty item that can hold about one standard sized soda/beer can with some Ice.
thingiverse
This is for the 2 front latches for the 120 quart igloo cooler. The ones it comes with are very flimsy and break off easily. ... You will have to use a flexible material like TPU