inkjet printhead arduino 3d models

Hello There,So I am printing on a private and I encountered several times that my filament would "run out" on a longer print on like the last layers.So what I did was move the filament sensor directly to the printhead with this sensor holder.I...

Avaiable at cults3d: https://cults3d.com/en/3d-model/tool/poison-printhead-v4-twotrees-sapphire-plus-pro This is my own design, inspired by the vzbot printhead. I made this for the Twotrees Sapphire Plus (SP), but I think it will also fit on the Pro....

I've included the goliath fan duct which leaves room for the BL-Touch but the other Vz-Printhead fan-ducts should work with the normal bottom plate. You can find a BOM by searching for "Vz-Printhead-printed" I have also uploaded the step files on...

I've included the goliath fan duct which leaves room for the BL-Touch but the other Vz-Printhead fan-ducts should work with the normal bottom plate.You can find a BOM by searching for "Vz-Printhead-printed"Thanks Vez and MirageC for the Vzbot and...

Another Anycubic i3 mega printhead light, a first draft for testing. The assembly is done without gluing, just solder and plug. All cables are hidden, very thin cables are required. In my junk box, I found four white LED 3mm, which were intended...

To solve this problem, I created a small device that fits snugly between the printhead and the cable loom, preventing the cable clip from slipping out of place once it's in position. It's quite tiny, but what a difference it makes for my printer! ... ...

I made this supported fan duct for the Phaetus Rapido HF/UHF it is designed for use on the VzBot Printhead (purchased through F3D racing!!) utilizing the Rapido hotend with a 2510 fan. I recommend using a stiff material like ASA/CF or PC/CF Use...

This part is captured by the existing hardware on the printhead, and the existing M2.5x10 screws are used to attach the fan to it. I did not test to airflow improvements, but it doesn't seem to have caused any negative effects. The idea is to...

This part is captured by the existing hardware on the printhead, and the existing M2.5x10 screws are used to attach the fan to it. I did not test to airflow improvements, but it doesn't seem to have caused any negative effects. The idea is to...

Any accessory mounted on the left side of the printhead will have to be removed in order to open the hatch - this was fine for my application, as I have a BL touch mounted on the left, and the position needed to be adjusted when swapping between my...

Anycubic Predator effector designed for use with Stoneflower3D printhead kit V2 on 3D ceramic printers. UPDATE !! ...04/10/2020 Second version features: - A more powerful motor (Nema17 65Ncm - 92oz.in) installed to enhance performance - The new...

See our Assembly Guides page here: http://versatile3d.com/components/assembly-resources/ Printhead 3D Printer Assembly Includes the following 3D printed components... PF-GR01 Guide Rod Holder PF-BCK01 Belt Clamp Knob* PF-ZK01 EzJust Lock Knob...

This is the Version 2 of my own design, the Poison printhead. It's designed for the TwoTrees Sapphire Plus, but I think that it will fit on the pro too. It's designed with a dragon-hotend, Orbiter extruder, 5015 fan, 40mm fan, bltouch, accelerometer...

#Anycubic i3 Mega S printhead cable strain-relief I designed this because I did not find a simple cable strain-relief for the Anycubic i3 Mega S that didn't require an elaborate print. Also, I route my cable via the front instead of under the arch...

Also included is a modified copy of the Elegoo Neptune 2 Firmware enabling BLtouch use and adjusting the setting for the location of the mount on the printhead. Disclaimer: please use this firmware at your own risk, I do not accept responsibility...

#Anycubic i3 Mega S printhead cable strain-relief I designed this because I did not find a **simple cable strain-relief** for the ***Anycubic i3 Mega S*** that didn't require an elaborate print. Also, I **route my cable** via the **front** instead of...

This is my tronxy printhead, it attaches an orbiter 1.5 extruder to the stock cooler and fan, and adds a 5015 radial blower for part cooling. *Update* added V3 nozzle and v2 fan mount. this makes the fan mount stronger, and improves part cooling...

If you'd like to discuss this project further, feel free to do so here: http://umforum.ultimaker.com/index.php?/topic/9907-ultimaker2-modular-printhead/. I've also used an interchangeable "olson block" nozzle on my Ultimaker 2, which is available...

Then you attach it with 3 screws on the top of the printhead (see the photo). I have included different versions of casing, feel free to remix them</p><p>The cooling duct holder is attached instead of stock fan. The duct is then attached with M4...

Creality Printhead Sidefanbox for 40x40x20 Noctua deutsch unten 2021July02: WARNING: my expierence now: perhaps the necessary stepdownconverter 24V to 12V are damaging the upper left chip on the small PCBboard whre the flexible cable comes to the...

... The design is based on my previous E3Dv5 hotend mount, which itself was inspired by Nick Foley's "E3Dv5 integrated printhead" published on Thingiverse.com. My primary objectives with this new design were: 1. Achieve solid and reliable performance.

A highly detailed appliance model is available, complete with textures, shaders, and materials. Ready to use, simply place it in your scene. This model can be found in Archmodels vol. 35. Available formats include 3ds, dxf, max, obj, scanline *.max,...

Experience a highly detailed appliance model, complete with textures, shaders, and materials. Effortlessly incorporate it into your scene for an immersive experience. Originating from Archmodels vol. 35, this model is available in various formats:...

Crafted for compatibility with standard Arduino Uno boards, this enclosure also accommodates an Arduino and a shield (tested successfully with an Ethernet shield). Featuring two holes to securely attach to a MakerBeam profile, the robust design...

Arduino Card Holder and Stand This is a box that serves as a holder for the card and preserves the welds of the contacts while providing a cache to close the assembly, securing the transport of the card. ... Layer Thickness: 0.2 Hull Thickness: 0.6 Fill...

Arduino card holder and holder Here is a box that will serve as a support for the card and preserved the welds of the contacts and a cache to close the assembly, which secures the transport of the card. Layer thickness 0.2 Hull thickness 0.6 Fill...

Als Alternative zum Akku kann man um kosten zu sparen den Arduino und die Wasserpumpe über den DC-Adapter direkt per USB betreiben. Die Wasserpumpe wird über das Relais gesteuert, da der Arduino nicht genug Ampere liefern kann. Du brauchst: Arduino...

Arduino Mega

Arduino UNO

Arduino box