itx case 3d models

I've designed some custom shelves for my Warhammer 40K model painting supplies, including paints from various manufacturers. The system allows you to mount two shelves on either side of a wall and connect them with chains. For instance, you can...

being able to reprint the broken part vs the entire model is a plus. Except for the charging ports, no glue is needed. All the STL files have been positioned to hide the seam as much as possible (when possible). The Activator Assembly parts are...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

Here is a 1:1 scale model of the first rover called Sojourner =) The frame is assembled from a 20x20 mm structural aluminum profile. All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

If you look at the print of the base (or the model of the legs) you will see there is a round hole with three slots surrounding it. These slots fit a specialized washer that is used in the vise to keep the base from rotating when it has been...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

The bowl model is a solid piece, and CAN be printed in vase mode / spiralize outer contour. This, however, isn’t the strongest. What I do is print them with 0% infill, 2-3 outer walls, 4 bottom layers, and 0 top layers. Basically makes it a double...

1x M6 square nut - model allows for 5mm thick, 10mm square 1x M6 set screw (10mm length recommended) Important: while printing you MUST put a pause at the layer just before the nut is covered up. Look for the small "box" cavity in-line with the...

I added a switch at the bottom of the right arm (super easy access).To fix the led support, you will need 2 M5x12 screws (Original, it bottom 8mm long, they are little short, you will need 12mm minimum, if it is longer, it is not annoying)I haven't...

... with the not dampened stepper motor. Ein von Martin Majewski (@martinjmajewski) gepostetes Video am 5. Nov 2016 um 4:50 Uhr Update 3: I removed the V1 models as they seemed to have some issues. ... V2 is the most current and best working version.

A remix to iTrooper's version https://www.thingiverse.com/thing:707734 Update 03.07.2022Models updated with new dimensions that is close to FreeTrack's suggested hardware dimensions.Only difference is the distance between the two front LEDs (82mm...

... The models are in the position, they should be printed. No support is needed. I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this tall piece. Printed on an Ender 3 Have fun!

At first I tried to make my own design modeled more closely after the one that I found, and it worked ok but it had one pretty significant flaw. Unlike my inspiration design, versions A and B limited the filter surface area to a surface area only...

This model drops excess wind The concept is to use it quietly This mod may be a bit more difficult 5015-24v fan 5015-12v or 24v fan * Please note that the polarity of the fan electrodes may be reversed. DC-DC adjustable step-down power supply I...

Please note that this model doesn't include the hooks on the bottom for the external antenna coupling. My car doesn't have one but I think it can be added easily. You can find the assembly instructions in the print instructions or here at...

I design a Electronic Bay Cover with LED Light Just a little favour>>>Less then 10% of downloaded Models get a like.→ If you like the design, it will be nice if you click on the like button and maybe share your print.   Its a heavy redesign of the...

... (option code 772). From VIN F060888 1999 Mercedes-Benz CLK430 Base Coupe 2-Door 4.3L 4266CC V8 GAS SOHC Naturally Aspirated Included formats: *.obj, *.stl, *.3mf All dimensions are accurate. This model printed and tested successfully.

The firmware numbers will match regardless of your printer model. If you use a slicer that requires EEPROM, make sure to update your EEPROM settings to match your new firmware. The easiest part is printing the adapter plate - any ABS or PLA preset...

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Ranger from Nan Thalias. Ervion was sent as part of an Elven diplomat’s escort, alongside his father which was attacked by a retinue of goblins and bandits near the County...

for the Firebrigade, working at hightSimilar thing on picture https://www.thingiverse.com/thing:6500617The most important mounting hardware used:-2mm dia tooth picks-3.2mm dia Mikado game sticks.-3.5mm metal screws for plastic (no machine screws!)The...

If you're using another fan make and model, make sure you check the polarity so it isn't reversed. If you don't have crimping tool you can just cut off the connector from the original fan and solder/splice it on.</p><p>Print the 3 (4) parts. If you...

This model is equipped with forklift skid pockets, locking casters, and a top located lifting eyelet which allows easy lifting with cable or chain hooks.Applications: Converting 690 V local grid power to 415Y/240 for on-site equipment. ...This 30 kVA...

IMPORTANT INFO REGARDING ARRMA 6s REAR HUBS: There are basically two versions of the Arrma 6s rear hub between all the 6s models (36mm wide and 45mm wide). <b>The recommended version are the hub parts used in the 6s Kraton/Notorious/Outcast which...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   One of the few Colossals on Tharador not to be born in the bitter Frozen Wastes of Oldavor. Harmara is also one of the few hemomancers to exist out the bounds of Oldavor, the...

The model is optimized for the connectors shown on the pictures. Super glue/cyano acrylate/any other transparent fast setting glue which adheres to your filament. Wire (should be thick enough for 700 mA and thin enough to fit into the carrier ...

This model is only to demonstrate the principle, not to resemble the original (destroyed) or replica (Deutschen Technikmuseum, Berlin, Germany: https://sdtb.de/museum-of-technology/exhibitions/1256/). This is an improvement of <a...

We'll be using a simple character model for this exercise, so go ahead and import it into your scene. You can find the model in the "Models" folder of your project. Once you've imported the model, select it and go to Edit > Object > Group. Name the...