j channel led lights 3d models

This is a 3D-printed 90deg corner for aluminium LED-strip mounting channels. (https://www.puuilo.fi/Airam-alumiiniprofiili-led-nauhalle-1m-Basic) I quickly designed this to finalize the RGB-LED installation to my son's gaming desk. Also and "end...

A compact and versatile module for extending LED light strips. ...Connect it seamlessly to build longer, brighter installations.

90 degrees inner (plain, no supports) https://www.tinkercad.com/things/4W1ptx2Z7iW-led-channel-joiner-inner-90-deg 90 degrees outer (plain, no supports) https://www.tinkercad.com/things/iFejkWHJzMJ-led-channel-joiner-outer-90-deg- junction box at...

This is an outside corner diffuser elbow for the 45° LED strip mounting channel. For whatever reason, at this time they do not make one for turning outside corners. ... Added a 120° for a roof gable top corner I needed.

This is an outside corner diffuser elbow for the 45° LED strip mounting channel. ... For whatever reason, at this time they do not make one for turning outside corners.

Instead of using an aluminum channel, you can print a holder for your LED strip yourself. If you want it longer or shorter, you can easily scale it on the y-axis. If you have a question or problem, please contact me. It seems like in some...

Instead of using an aluminum channel, you can print your own holder for the LED Strip. If you want it longer or shorter, scaling on the Y-axis is easy. Got questions or problems? Contact me. Note that some programs require scaling to 1000% to get the...

This is an outside corner diffuser elbow for the 45° LED strip mounting channel. For whatever reason, at this time they do not make one for turning outside corners. Added a 120° for a roof gable top corner I needed. ... Print Settings Supports: Yes ...

If you do that make sure to clear the feet on the base.These are the LED aluminum channels I used. I bought some about a year apart, the newer ones were a mm smaller than the old ones and it made a difference for the press fit. I included the...

This is a clip designed for mounting 45° LED channels to any surface. For plastic surfaces, crazy glue or any fast-bounding glue is recommended. For wooden surfaces, there are two holes in om the model for wood screws. Do not tighten the screws too...

This is an insert I created to use in Muzata U103 channel so that I could run power (for power injection) and data (for bringing back the DO from the end of the LED strip) lines in parallel with the LED strips. I made it so that the wires ran under...

... which is translucent and illuminates. The cover pieces are not glued, they are just fitted. The leds should be glued to the inside wall of the letters and pass between them through the existing holes. ... Size of 14 cm in height and 3cm in depth.

**If you get a 404 error when trying to download, go to the "Thing Files" tab and download them individually.** This is a PVC pipe clip for J-Channel to hang Christmas Lights on. This was designed for 20mm schedule 40 PVC pipe. These are available in...

**If you get a 404 error when trying to download, go to the "Thing Files" tab and download them individually.** This is a PVC pipe clip for J-Channel to hang Christmas Lights on. This was designed for 25mm schedule 40 PVC pipe. These are available in...

Instead of the aluminum channels mentioned in the description for the LED light bar, I designed this alternative. I'm assuming roughly 20cm of LED light strip. Print instructionsYou need to print two of these for the project. ...The model fits, if...

I created this setup for drilling Certainteed 3/4" pocket J channel to accommodate rgb pixels for exterior holiday lighting. The 75mm spacing between pixels, which I've found works well with the Alitove WS2811 RGB's from Amazon, has been effective. A...

This is an extension of the light bar, not a remix of the end pieces themselves. Instead of the aluminum channels mentioned in the description for the LED light bar, I designed this alternative. ...I'm assuming roughly 20cm of LED light strip. Print...

3D printed clips to attach WS2811 Pixels in J-Channel to the soffit for Permanent LED Lighting. This was designed for the Ply Gem 5/8 in. x 1-1/2 in. x 12.6 ft. White J-Channel from Home Depot. For me the 7mm clip was the main one I used for...

This is a drill guide for the plastic J-Channel found at Lowes and Home Depot. ...Designed to hold 12mm Bullet Pixels for use in DIY holiday lighting.

Aluminum LED Channel brackets for the Ender 5/ Plus printers. You will need to print two of each file for all four needed. The brackets do not have holes for the wiring, but 10 seconds and a drill bit will put the hole wherever you want it. ...

While I was in there making edits I decided to add some nubs to better grab the sides of the 17mm aluminum LED channel as well as some zip tie through holes for better wire management options.Printing InfoYou can choose to print either the double...

Corners for 1/2 Ply gem J channel.

**If you get a 404 error when trying to download, go to the "Thing Files" tab and download them individually.** This is a PVC pipe clip for J-Channel to hang Christmas Lights on. This was designed for 20mm schedule 40 PVC pipe. These are available in...

**If you get a 404 error when trying to download, go to the "Thing Files" tab and download them individually.** This is a PVC pipe clip for J-Channel to hang Christmas Lights on. This was designed for 25mm schedule 40 PVC pipe. These are available in...

This is a step-by-step guide to installing the plastic J-channel, readily available at both Lowes and Home Depot stores, specifically designed to support 12mm Bullet Pixels for use in creating unique and festive DIY holiday light displays.

I found a stand that perfectly matches the standard lithopane produced by Cura. ...I bought LED strip lights and an AC adapter from Amazon online.

this Jig (5 .STL files ) is for J-channel on a 3" / 2.8" / 2.5" / 2" / 1.5" spacing for WS2811 LED's. Just drill your starting hole (free-hand) then slide it in the Jig, the Channel will slide across the "positive" stop ( should hear a click ) if you...

Remixed from https://www.prusaprinters.org/prints/37779-pvc-window-j-channel-clip I have made the clip long enough to help hide the bullet pixel wire under the PVC so that this wire is less visible from the front. A small channel allows the cable to...

A 2 piece clip system when placed together create a non-permanent way to hang year around pixel lights, mounted in J-channel, to the eaves (soffit actually I guess) of your house. The attachment created when the two pieces are slide together snaps...

A 2 piece clip system when placed together create a non-permanent way to hang year around pixel lights, mounted in J-channel, to the eaves (soffit actually I guess) of your house. The attachment created when the two pieces are slide together snaps...