k40 air assist 3d models
94581 3d models found related to k40 air assist.thingiverse
K40 Air Assist Takes fish tank air line 3/16 I bought the 8ft 3/16 Penn Plax Airline Tubing for Aquariums for like 2$ amazon. ...
thingiverse
K40 Air Assist with Omni Nozzle to give an even air flow and not cause soot/kerf to be blown in a single direction. Non-enclosed so you can still use a height gauge between the material and the bottom of the laser/lens. Made from scratch in...
thingiverse
This is a laser cutter nose to add air assistance to your k40 (with stock head) with a 6/4mm air hose. ... It's meant to be cut in 3mm plywood (but anything 3mm should work as well).
thingiverse
My take on an air-assist nozzle for the K40 laser engravers. I haven't modified my exhaust vent yet, so had to make endstops to prevent the nozzle from crashing into the vent. ... The attachment hole on the nozzle was designed to be final-drilled...
thingiverse
Air assist nozzle for k40 laser, takes 3mm bolt to clamp onto head. The nozzle tip is held in by friction. The hole at the end of the nozzle tip is very small, unless your laser is well aligned your beam will likely miss this hole, and make its own!...
thingiverse
Air assist for K40 Laser with laser pointer mount. I used #6-32 hardware to attach to pointer mount. The quick connect air fitting threads directly into hole. ... Laser pointer link:...
thingiverse
This is the air assist nozzle I use with my K40 laser cutter. The design was created in OpenSCAD and I have included the OpenSCAD file that can be modified. The coiled hose and fitting I used are listed below. The fitting that I used to attach the...
youmagine
This is the air assist nozzle I use with my K40 laser cutter. The design was created in OpenSCAD and I have included the OpenSCAD file that can be modified. The coiled hose and fitting I used are listed below. The fitting that I used to attach the...
thingiverse
Just a simple AirAssist for our beloved K40 Laser. ...Just slide it over ur lensholder and plug in ur air hose, fits really tight, if not there is a small hole u can use for a set screw. ... Made for the use with 6mm OD Silicone hose.
thingiverse
Air assist add on for laser cutter. Uses M3 screw to secure it to laser focusing lens housing and air blows directly on job. ... Air tube is set up so that no support is needed.
thingiverse
K40 Air Assist to avoid potential melting of 3D printed nozzle. ...Insert and glue in a standard metal basketball filling needle.
cults3d
Tube adaptor for K40 Air Assist. I printed the following air assist design https://www.thingiverse.com/thing:3318177 And used the following silicone tube https://www.amazon.de/gp/product/B077RCHSL9/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 And...
thingiverse
Tube adaptor for K40 Air Assist. I printed the following air assist design https://www.thingiverse.com/thing:3318177 And used the following silicone tube https://www.amazon.de/gp/product/B077RCHSL9/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1...
thingiverse
K40 air assist with holders for line lasers to use in creating a cross hair for aiming. The fit was a little loose, so I used a dab of hot glue to firm up the hold on the lens assembly. Also used a little hot glue to hold the air tube in. ... You...
thingiverse
Adaptor to fit Air assist and laser diode to the head of the K40. Laser diode is sight for 50.8mm. ... Requires: 2x M3 square nuts 2x M3x8mm screws 1/4" BSP press air fitting 5v laser diode
thingiverse
This is an air assist nozzle for a K40 Chinese laser cutter, based on the original model by VanBot112 and the remixed version by Venomouse. I changed the air inlet so that it comes in from the side because I'm using the [positioning laser mount by...
thingiverse
The was an attempt to design an air assist nozzle for the K40 printer. The nozzle works with the existing laser head and attempts to utilize lamar flow. So far I have had decent success with it but have not tested to see if has increased my cutting...
thingiverse
An Air Assist Nozzle for the Stock Laser Head on the K40 Laser Cutter. The aim of the project was to design and build a lamar flow laser head to increase the cutting ability of the laser. ...Initial testing has not been started but if you print this...
thingiverse
An Air Assist for a chinese K40 Laser which i designed for a friend. For mounting the fan i designed it to fit M4 nuts and bolts. To mount the main part you need 2 small wood screws and another 2 for the fan holder. For the air stream to get a...
prusaprinters
This is an air assist nozzle for a K40 Chinese laser cutter, based on the original model by VanBot112 and the remixed version by Venomouse. I changed the air inlet so that it comes in from the side because I'm using the positioning laser mount by...
thingiverse
I made these air assist holders for a small acetylene tip, For a year, I used a standard small aquarium air pump until it finally died. Upgraded to a piston version. Any small tube (copper or Brass) will work. Here are 2 mounts for an Air Assist...
prusaprinters
An Air Assist Nozzle for the Stock Laser Head on the K40 Laser Cutter. The aim of the project was to design and build a lamar flow laser head to increase the cutting ability of the laser. ...Initial testing has not been started but if you print this...
thingiverse
This is a simple mounting ring for the Air Assist with Dual Laser Nozzle by Demonic69:http://www.thingiverse.com/thing:1063067 and for the Air Assist by thevisadhttp://www.thingiverse.com/thing:1016720 I've glued it on top of the Air Assist and used...
thingiverse
Attach a fan to the K40 laser head. ... Use a M3 screw to clamp the ring around the head.
grabcad
Has a mount for a 50x15 12VDC radial blower for direct air assist doing away with need for tubing and external air pump. For targeting I use two 5mm diode lasers. below the laser is a hole for a 5mm flint glass rod to make a line from the lasers...
thingiverse
Printed @ 80% infill .2 layer height. Added screw holes (3.5mm) to hold in place on your machine. ... Accepts standard airhose Standard 1/8" BSP (its an 8mm thread)
cults3d
Air Assist / Smoke Assist / Air Nozzle for K40 Laser. Will fit on a standard 26mm OD laser Head and is held in place by two short M3 Bolts. The nozzle has an inlet port designed to fit a 6mm OD PVC tube. ...To make a smaller opening for the air outlet,...
thingiverse
Air Assist / Smoke Assist / Air Nozzle for K40 Laser. Will fit on a standard 26mm OD laser Head and is held in place by two short M3 Bolts. The nozzle has an inlet port designed to fit a 6mm OD PVC tube. ... To make a smaller opening for the air...