kailh choc switches 3d models
67703 3d models found related to kailh choc switches.thingiverse
It is a compact light-weight split keyboard, a version of my Crocodox keyboard for Kailh Choc switches. It may also work for the regular Cherry MX switches as their base size is the same 13.5x13.5, but there will be not enough space inside for the...
thingiverse
Blank keycap set for kailh choc switches and kailh plate mounted stabililzers, should be used with 18x17mm spacing. ... Featuring: 1u,1.25u,1.5u,1.75u, 2u, 2.25u, 6.25u, and 2u vertical (with horizontal and vertical switch mount, you still might want to...
thingiverse
This is a new version of the Crocodox keyboard with the Kailh Choc switches. It is a remix of the previous version: https://www.thingiverse.com/thing:4840523 I moved the pinkie columns a bit and swapped the way the top and bottoms are...
thingiverse
Also I wanted to use the Cherry-MX keycap-compatible Kailh switches for which I do have a nice set of key caps, but I completely forgot about difference in their size, so I used the "regular" Kailh Choc ones. So this is just another interim design on...
thingiverse
Spring-swapped Kailh red switches with some leftover caps are used. ProMicro inside, QMK Planck-based firmware. ... Fusion 360 project is here: https://a360.co/2YRA7ee UPD: I've created a version with a smaller bend angle, it is more comfortable...
prusaprinters
I wanted a plate to put Kailh Choc switches and hotswap sockets into for a small project with a Raspberry Pi, but I couldn't find anything that suited my needs. I love mechanical switches and hope to use them in many projects requiring buttons, so...
thingiverse
A remix of my Fish Ladder Mk.3 keyboard (https://www.thingiverse.com/thing:4828205) to use Kailh Choc switches. I swapped the springs to 12gf and removed the stabilizers from them. The switches are holding in holes by friction only. Keyboard is...
thingiverse
This is a remix and a rebuild of the previous version. 60 degrees between the hands turned out to be too much, so I reduced it down to 44 degrees. Another big change is the thumb keys raised 8 mm above the rest. Much better this way and it does not...
thingiverse
A version with reduced angle between the hands. The thumb keys raised 8mm above other keys. The previous version with 60 degrees bend turned out to be even less comfortable than the very original one with its 30 degrees between the sides. So I...
thingiverse
A rebuild of the previous version with smaller angle between the sides, with the thumb keys raised over the rest of the keys.
prusaprinters
I'd be happy about feedback. This is a switch puller for Kailh Choc V1 (PG1350) Switches. It will only work with switches in a plate.Layer height doesn't really matter, as it is used upside down and will always be flat. ...If you find that you have...
thingiverse
The original design didn't fit; the legs were a bit too close together and short to fit and stay in the switch (I understand this is a slight difference to the low-profile choc switches on Havit keyboards). ### Changes: - Made MX end thicker for...
prusaprinters
The original design didn't fit; the legs were a bit too close together and short to fit and stay in the switch (I understand this is a slight difference to the low-profile choc switches on Havit keyboards). Changes: Made MX end thicker for tighter...
thingiverse
This is a simple tool to help open Kailh Choc V2 mechanical switches with reduced risk for damage while requiring less precision and time. I appreciate any comments with details of your experiences with successful and unsuccessful prints/uses you...
thingiverse
I made this so I can use Kailh type keycaps, on a Keychron low-profile switch. ...Has notches for using a key-puller to remove the adapter if necessary.
thingiverse
Värdera — custom designed low-profile keycaps for Kailh Choc switches. ...Comes with special rounded thumb keycaps for better ergonomics and ease of use.
thingiverse
This is a little tool to help open Kailh Choc switches. There's just enough stretch on the tabs that they open but, should not be enough that they break. To use it, place the switch on the opener base then carefully lower the lid onto the top. Then,...
thingiverse
This uses wires between the original through-holes and the pins of the choc switches, since they'd otherwise be too low with the stock kailh choc switches. ...I designed to to be a snap fit, and though it did work, I think it was a bit too tight and...
thingiverse
## Compatibility The keycaps were designed for the Kailh Choc switch. They should thus also be compatible with other Cherry MX style switches, yet the keycap will not cover the whole stem. ## Printing The model is designed to be printed with a...
thingiverse
KAILH Low Profile blank keycap. ...Designed to work with Kailh Low Profile Switches (kailh choc switch PG1350) I added both a hard edge version and rounded. ...Both versions have rounded corners.
thingiverse
PRINCE profile Kailh Choc keycap. ...Designed for SLA printing.
thingiverse
DIP profile Kailh Choc keycap. ...Designed for SLA printing or manufacturing out of sheet metal.
thingiverse
A keycap for Kailh Choc v1 low profile switches optimized for use in DIY boards like the Ferris/Sweep. Print upside down. Depending on your printer the connector pins might have to be adjusted. You can easily do this in the parameters...
thingiverse
An adapter that tilts a keycap on a choc switch. There are two files available so far: - choc_tilted will tilt the keycap vertically. ... - choc_tilted_rotated will tilt and also rotate the keycap 90 degrees.
prusaprinters
keycap for the flat mechanical kalih choc switches Print instructionsCategory: Computer Summary keycap for the flat mechanical kalih choc switches
thingiverse
I got some MBK choc keycaps for my gergo, but realized the 2u keycaps won't fit on the gergo, as the caps are horizontal and the switches are not rotated. This little adapter fits onto the tines of the keycap and has its own pair of tines, rotated...