kailh choc 3d models
640 3d models found related to kailh choc.thingiverse
PRINCE profile Kailh Choc keycap. ...Designed for SLA printing.
thingiverse
DIP profile Kailh Choc keycap. ...Designed for SLA printing or manufacturing out of sheet metal.
thingiverse
Värdera — custom designed low-profile keycaps for Kailh Choc switches. ...Comes with special rounded thumb keycaps for better ergonomics and ease of use.
thingiverse
A keycap for Kailh Choc v1 low profile switches optimized for use in DIY boards like the Ferris/Sweep. Print upside down. Depending on your printer the connector pins might have to be adjusted. You can easily do this in the parameters...
thingiverse
This is a little tool to help open Kailh Choc switches. There's just enough stretch on the tabs that they open but, should not be enough that they break. To use it, place the switch on the opener base then carefully lower the lid onto the top. ...
thingiverse
Keycaps for kailh choc low profile switches. I did the stabs by trial and error for my printer. They would likely need to be adjusted for your printer. ...Adjusting the part by scale would likely work for small changes These are designed for 16mm...
thingiverse
It is a compact light-weight split keyboard, a version of my Crocodox keyboard for Kailh Choc switches. It may also work for the regular Cherry MX switches as their base size is the same 13.5x13.5, but there will be not enough space inside for the...
grabcad
Kailh Choc V1 PG1350 Stabiliser modelled from the tech sheet listed by Kailh on their Ali Express store (I've attached that here as well)... I had to best guess some dimensions. But the fundamentals are there and I've manufactured a case and keycaps...
thingiverse
An adapter that tilts a keycap on a choc switch. ... There are two files available so far: - choc_tilted will tilt the keycap vertically. ... - choc_tilted_rotated will tilt and also rotate the keycap 90 degrees.
prusaprinters
keycap for the flat mechanical kalih choc switches Print instructionsCategory: Computer Summary keycap for the flat mechanical kalih choc switches
thingiverse
I got some MBK choc keycaps for my gergo, but realized the 2u keycaps won't fit on the gergo, as the caps are horizontal and the switches are not rotated. This little adapter fits onto the tines of the keycap and has its own pair of tines, rotated...
thingiverse
Arcade Controller Button(kailh choc v1) Snack Box Micro
thingiverse
Arcade Controller Button kailh choc v1 Snack Box Micro shadow 5.5S-01
thingiverse
Blank keycap set for kailh choc switches and kailh plate mounted stabililzers, should be used with 18x17mm spacing. ... Featuring: 1u,1.25u,1.5u,1.75u, 2u, 2.25u, 6.25u, and 2u vertical (with horizontal and vertical switch mount, you still might want...
thingiverse
This uses wires between the original through-holes and the pins of the choc switches, since they'd otherwise be too low with the stock kailh choc switches. ...I designed to to be a snap fit, and though it did work, I think it was a bit too tight and...
prusaprinters
I'd be happy about feedback. This is a switch puller for Kailh Choc V1 (PG1350) Switches. It will only work with switches in a plate.</p><p>Layer height doesn't really matter, as it is used upside down and will always be flat. ...If you find that...
thingiverse
## Compatibility The keycaps were designed for the Kailh Choc switch. They should thus also be compatible with other Cherry MX style switches, yet the keycap will not cover the whole stem. ## Printing The model is designed to be printed with a...
thingiverse
A keycap for Kailh Choc v1 low profile switches optimized for use in DIY boards like the Ferris/Sweep. Print upside down. (Rotate 175deg since its 5deg top angle ;) ) Depending on your printer the connector pins might have to be adjusted. You...
thingiverse
This is a simple tool to help open Kailh Choc V2 mechanical switches with reduced risk for damage while requiring less precision and time. I appreciate any comments with details of your experiences with successful and unsuccessful prints/uses you...
prusaprinters
I wanted a plate to put Kailh Choc switches and hotswap sockets into for a small project with a Raspberry Pi, but I couldn't find anything that suited my needs. I love mechanical switches and hope to use them in many projects requiring buttons, so...
thingiverse
Also I wanted to use the Cherry-MX keycap-compatible Kailh switches for which I do have a nice set of key caps, but I completely forgot about difference in their size, so I used the "regular" Kailh Choc ones. So this is just another interim design on...
thingiverse
This is a new version of the Crocodox keyboard with the Kailh Choc switches. It is a remix of the previous version: https://www.thingiverse.com/thing:4840523 I moved the pinkie columns a bit and swapped the way the top and bottoms are...
thingiverse
Use a brim unless you like to live dangerously. ...Will print with a 0.4mm nozzle, but for best results use 0.2.