kassandra 3d model

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

Just go on Amazon or Ebay and get a metal vice and then bolt it down securely on your workbench.The specs for this little guy are:40mm jaw opening20mm jaw widththroat depth 12mmThanks to a metal screw (M6x60) and an M6 metal nut as inlay, it is...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism is...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

The tubes used for processing in the Whirlwind would end up leading Ken Olson to transistors, which led to the transistorized TX-O (the love of many a tech model railroad clubber) and later to Olson founding DEC. Suddenly, the Whirlwind was the...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

If your name is not Matt, then there is a template attached in the model files called “Name_Plate_Template”. If you wish to add your own name to this template, open the attached file called <code>Name_Plate_Template.step</code> in a CAD software of...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Wiring/Plug: This waterproof power supply is...

Its light and super stiff if printed in ABS 100% infill. Included are all the .STL files for all the models. The frame is quite light and stiff. I threw the frame over and over against a wall and from a 5th floor balcony and it survived...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...

Also, no screws or other fixing methods are used. How it works can be seen in the video UPD I added a version in two sides in the form of frames, its printing a third faster and when printing a model, corners closed by cooling by a fan are not...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

EX6 Arcade Fight Stick What started as just doing a few tweaks to an existing model turned into a near full redesign and a (almost) fully printable arcade/fight stick case platform; the EX6. Printable on the Ender 3 or any 200x200 printer. The...

To split it with ease, right-click on your model within Cura. When preparing your parts for printing, make sure flat sides are aligned downward. For a smoother print process, consider setting 0.1mm layer height and 40% infill as defaults. Here is...