keg tap heads 3d models
154166 3d models found related to keg tap heads.thingiverse
Flush your lines! ...keep your kegerator lines clean with this keg tap hose adapter.
thingiverse
Keg Tap Handles that you can add your own logo. ...Bottom of tap uses 3/8-16 inserts from McMaster-Carr.
thingiverse
Designed with 3/8-16 thread which should fit most taps. ... Use adhesive to secure white-board paper onto tap handle face to be able to write with dry erase markers when you buy a new keg for your kegerator!
thingiverse
I thought a barrel would make a nice tap handle for a beer keg so I threw one together from a couple great sources here on Thingiverse (see derivatives). Instructions Print as solid as you think...
thingiverse
... I designed. ...The handle accepts 3/8" bolts and this display attachment has just that, so it just screws in. This displays the little plastic cap that comes on your keg that typically has the beer or at least brewery info on it, so you can display it.
thingiverse
So I printed a small mount to connect a default german (probably also other) beer tap to the handle of a 9L NC Keg. Currently this is very tight and honestly bad fit which needs a lot of fine tuning (there is a radius in the handle I didn't account...
thingiverse
What it fits: I think there are two sizes of Cornelius kegs, taller/skinnier ones (which I believe are Pepsi) and shorter/wider ones (which I believe are Coca-Cola). I only have the taller ones, so this fits them (outer diameter between the rubber...
thingiverse
This is to allow additional support on both sides of keg shaft, when installed in a fridge door This model was made in Morphi! http://www.morphiapp.com. In Morphi, people of all skill levels can make 3D printable models on the go using touch, without...
thingiverse
Tap handle lock with adjustable screw. Works great on my setup! I used PLA with supports - lay the main body on its side and print with supports. The bolt prints fine standing without supports. ... PETG would be ok, but the higher stiffness of PLA is...
thingiverse
I wanted to create a simple little tag/label for my different home brew beers. ...This fits between the handle and tap and you can print a small label of your own design on top. ...The round label is 55mm in diameter.
thingiverse
A simple tap handle. There's a recess for a label, sticker, or paint it with chalkboard paint. Glue a nut in the bottom and screw it on. ... Use some washers or cardboard shims to fix the rotation if the thing doesn't face forward when it's fully...
thingiverse
Tottenham Hotspur cockerel emblem made into a keg tap handle. ...For use with a threaded insert (sold seperately) that matches your tap assembly.
thingiverse
A simple anti-splash drip tray that sits at the base of a standard keg. ...Two part construction.
thingiverse
Simple tap handle for your kegerator. ...It's threaded 3/8" at the top and the bottom. Bottom goes onto your tap, top so you can print changeable attachments. ...I also made an attachment that displays what beer is in the kegerator, for instance.
thingiverse
Tired of trying to get your Ikegger adapter unscrewed from your tap by hand cause it is too tight? This wrench will help you! ... Fits perfectly well without further tweaking.
myminifactory
Location: Eagle Tavern site on UNC Campus (RLA-Or257), Orange County, North Carolina. Notes: North Carolina Archaeological Collection, Research Laboratories of Archaeology, the University of North Carolina at Chapel Hill. Model by Chris LaMack.
thingiverse
... top. It's a little bit loose, so I might adjust the diameter a bit, but it's just fine the way it is now. The threads on the bottom are modeled into the piece and I was able to screw it right onto the tap without even cleaning them (no supports).
thingiverse
• Operates solenoids on each of the 5 taps, allowing me to only have them open when I want to pour a beer (primarily for kid and baby-sitter proofing, but also great to avoid accidental leakage). • Measures the temperature in the keezer. • Turns...
thingiverse
This is a wall mount for picnic tap. ...It has a press fit to make it quick and easy to use the tap. ... I used a 3 mm screw to mount this bracket.
thingiverse
A classic style tap handle with optional name plaque. There's a recess for a label, sticker, or paint it with chalkboard paint. Glue a nut in the bottom and screw it on the tap. ... Use some washers or cardboard shims to fix the rotation if the thing...
thingiverse
Ben Tov This model was made in Morphi! http://www.morphiapp.com. In Morphi, people of all skill levels can make 3D printable models on the go using touch, without wifi or a mouse. Download the app for free in the App store. ...
prusaprinters
I wanted a Keg Tap for my Lego Barrel, I got from Theo. https://www.printables.com/model/231577-large-brick-barrel
cgtrader
Real 3D Draft Beer Features refrigeration unit and fill tray with Keg , pump and Tap. the figure is automated and the beer mug can be filled. Also included are substance PBR textures see demo video at https://drive.google.com/open? also in props is...
thingiverse
... inside of the handle. More information on the project at ryansprojects.tech In order for this to thread on to a typical keg handle, you will need to glue a nut into the bottom of it. ...Add shims if necessary to get correct positioning.