kenwood th d72a battery 3d models
78861 3d models found related to kenwood th d72a battery.thingiverse
This is a holder for a Kenwood TH-D72a hand held radio. I find that the battery drains if I leave it connected, even with the radio off. So I designed this to hold two batteries behind, and the radio in the front. It is generic enough that it can be...
thingiverse
The Diamond SRH77CA antenna is a popular aftermarket upgrade for the Kenwood TH-D72A radio. The antenna base has a diameter of 11mm and the radio accepts antennas with a diameter of up to 17mm. This is a spacer to fill the gap between the antenna...
thingiverse
Designed up this to be able to use two 18650 batteries with my Kenwood TH-F7. Need wiring and if you want to charge on board need battery protection circuit. ... Version 2
thingiverse
TH-D74 is a really cool radio, but it's a bit of a battery hog. If you're going out for more than a few hours you might want a spare battery with you. This is a cover to protect the internal terminals. It also have an indicator switch you can toggle...
thingiverse
A cup/thing that mounts to a flat vertical surface that I can drop my TH-D74A into without worrying about dropping it on the concrete floor below (if not for that, I'd just use an old belt). Front loop for clipping a speaker-mic onto. OpenSCAD...
thingiverse
Using the TH-D72A antenna spacer as a concept this bushing was created in Fusion360 for the Kenwood TH-74A with a Diamond SRH320A tri-band antenna. The bushing fills the empty space around the Diamond antenna and likely provides a level of strain...
thingiverse
Bought a Kenwood TH-D74A, and decided I needed a Desk Stand for it.
thingiverse
Here is a simple desk stand for the Kenwood TH-F7 handheld transceiver. Please test if v3 fits correctly. ...The old design was too small.
thingiverse
The protective shell of the antenna of the kenwood TH-K2 (see picture) does not age weel, and inevitably brake down. It happened to me twice in a row. In made this shell as a replacement from the original. Unfortunately, I do not have flexible...
thingiverse
This is a 3D printed case for the Kenwood TH-D74A ham radio. I printed this in TPU material and it fits well. You can access all the controls on the front and sides of the radio and the back clip holds the case in place. The flat bottom allows the...
thingiverse
This is just a simple desk stand for my Kenwood TH-D74A. It's a pretty expensive radio that I didn't want getting dinged up, so I bought a soft case/cover for it. Unfortunately, with the cover in place, the radio does not stand up on it's own such...
thingiverse
From Randy - W4LKS May 2020 Kenwood TH-D74 3D Printed Desktop Stand Here is a simple desktop stand that holds the '74 at a pleasant angle for viewing the screen while it sits on your desk. The base is wide enough so it would be hard to knock it over....
thingiverse
First iteration of a ram mount compatible I made for the kenwood TH-D72 as there were none available I really liked. Notes: - Made to be used with the factory belt clip, it holds it in nice and snug - I have not yet tested this so may still...
thingiverse
Drop-in desk charger for Kenwood TH-F6 handheld radio
thingiverse
I wanted a decent stand / holder for my Kenwood TH-D74 Radio when I use it in the house, or a better more secure way of holding it in my car. So I designed this stand and after several iterations, settled on this version. Features include: -...
thingiverse
September 2020 From: Randy - W4LKS Holder for Kenwood TH-D74 handheld ham radio designed to attach to a RAM mount to allow mounting on handlebars, dashboard, windshield, etc. Requires a RAM diamond base like this one: ...
thingiverse
https://www.tinkercad.com/things/4WyS8fxde3D new: TH-D74 Halter_2.stl thinner Version. new: TH-D74 Halter 3.stl . ...Modified for new 4 Quick-FIX HR-Adapter.
thingiverse
Battery Cover for KENWOOD RC-R0628 lost mine so created a new one, got sick of changing the sellotape when i needed to change or jiggle the batteries to kick some life back in to the remote
thingiverse
Lost the control knob from the top of my handheld amateur (ham) radio. So I made a new one that I actually like better. Should friction fit so that it won't fall off. ... If not put a small drop of silicon caulking in the hole and it will stay on the...
thingiverse
replace 2 CR2032 batteries by a rechargeable battery. ... battery size: 402025 with protection charging circuit: TP4056 (type c) and charging current set to 0.1mA (by 10k setting resistor) also, 3.3 LDO is used
thingiverse
I was tired of my radio sitting the cup holder on my way to work and I didn't have my mobile installed yet, so I made a cradle for my HT that would allow a charger cable and antenna wire to come out from the dash when in use. There was an essentially...
thingiverse
Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.
prusaprinters
<p>Screw it to a wall or use it as a table stand, or create a custom mount for what ever you like to attach you radio to.</p> <p>To use it as a desktop stand you will need:<br/> 1x 25mm M3 screw (not counter sunk)<br/> 1x M3 nylock nut<br/> 2x M3...
thingiverse
A sleeve designed to protect buttons from being accidentally pressed (even though locked) but more importantly to stop side entry PTT cables from being pushed on when stowed and breaking the connector.
cults3d
Screw it to a wall or use it as a table stand, or create a custom mount for what ever you like to attach you radio to. To use it as a desktop stand you will need: 1x 25mm M3 screw (not counter sunk) 1x M3 nylock nut 2x M3 flat washers I got a...
thingiverse
A simple NB-L5 battery adapter, from a 18650 battery cell. You can just use an old laptop battery cell for this. This is compatible with Minidisc player Kenwood DMC-G7R. ... Tags: NB-L5 NBL5 Kenwood DMC-G7R DMCG7R Minidisc
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573