kossel pro 3d models
77917 3d models found related to kossel pro.thingiverse
This spool holder is designed to mount to the base of the kossel pro and clear my enclosure which sticks about 40mm from the frame extrusions.
thingiverse
I made an end effector for the Openbeam Kossel Pro that allows it to use an E3D hotend while maintaining support for the really good looking PCB included in the kits. The part isn't perfect and is definitely a work in progress but I wanted it out...
myminifactory
For best results, print with MatterHackers PRO Series PLA These mounts are for upgrading the Kossel Pro to use Force Sensing Resistors (FSRs) for automatic leveling, instead of the stock probe with a mechanical switch. See this forum post for a...
thingiverse
I designed it specifically for my Kossel Pro with a BL Touch autoleveling probe, but it should work for any printer with the specified hotend or similar ones. The radius of the cooling pipe lets enoguh space between the 3D printed part and the...
thingiverse
This piece should help keep you from snapping off the usb connector from your brainwave board on your openbeam kossel pro if you bump the connector or tug the wire by accident.
youmagine
If you want to have solid rubber feet attached to your OpenBeam Kossel Pro you can print you three of these mounts and attach them together with three 38 mm diameter rubber feet to your printer.
thingiverse
Use the inset holes to attach this to a horizontal rail on your Kossel Pro with the included (in your Kossel kit) M3 x 6mm BHCS screws. ... Instructions My print settings for this part were: 0.2mm...
thingiverse
Improved endstop mounts for the Kossel Pro (15mm extrusions) Improvements over the stock mounts: -offset so that the belts don't rub on the screw heads, causing artifacts -rest against upper frame triangle so they stay stationary after repeated...
thingiverse
Kossel Pro Viki 2 lcd Mount Mounts directly to the kossel pro frame. ...It sticks out a lot to clear my enclosure.
thingiverse
It attaches to an aluminum 1515 OpenBeam extrusion using two M3 x 6mm BHCS (or the longer M3 x 8mm SHCS) that are included in the Kossel Pro kit. Version two of the [original spool mount adapter](http://www.thingiverse.com/thing:642171) adds two...
thingiverse
you can print this mount and attach it onto one of the Kossel Pro's upright extrusions. There is a little lip printed on the open side to keep the holder from easily sliding out, so to release, pull the holder up, and out. Updated 2015-01-21: The...
thingiverse
This replaces the tall bed clamps that came standard with the Kossel Pro, which interfere with the printhead when it's at the edge of the bed. Made in OpenSCAD, file included, there's not much to it. Remove the old bed clamps. If the nuts inside...
thingiverse
Low Profile Bed Clamps for the Kossel Pro These bed clamps sit only 2mm above the print surface, which greatly improves the printing area compared to the stock bed clamps. The screw heads are recessed so that they sit flush with the bed clamps. This...
thingiverse
Just a simple spool holder for the Kossel Pro that connects to the vertical OpenBeam piece and positions the spool at the right angle to feed into the filament drive. It clips onto the beam, but also includes a hole for a screw in case the clip...
thingiverse
I designed it specifically for my Kossel Pro with a BL Touch autoleveling probe, but it should work for any printer with the specified hotend or similar ones. This version works with 40x40 mm axial fans and it is an adaptation of the original...
thingiverse
This is a fan upgrade for the Kossel Pro delta printer or the Kossel RepRap variant that uses the same stock effector. The stock effector uses (3) diminutive 10mm 5V fans; (1) for the hot end and (2) for part cooling. Sadly, while the fans are...
thingiverse
Some part is update for nice mechanical Filament spool holder :https://www.thingiverse.com/thing:454808 All is printed 0.2mm infil 15-20% Enjoy
thingiverse
Looking for a Ros Damper , found a few of them but i want no zip ties or rubber Band. ... Decided to make my own ;) Print in TPU or similar
thingiverse
ball bearing spool holder for the kossel pro used bearings from a bike's bottom bracket. (42mm OD, 30mm ID) mounts to a 15x15mm extrusion using m3 bolts at 30 or 60 degrees. ...fits 1kg rolls with a bit of wiggle room.
thingiverse
I raised my Kossel pro to attach the PSU under the printer. This left my figures free to slip under the LED panel while using the screen and possibly touching the circuits. This extended panel goes down to the floor. It looks a lot neater too. ... ...
youmagine
see the older version 3: http://www.thingiverse.com/thing:1765913 Parts List: E3d V6 Hotend 3x 30x30x10mm fans 24V or 12V depending on your printer 9x #4 5/8" thread rolling screws for plastic (amazon) 3x 5x37mm internally threaded tube (comes stock...
thingiverse
However due to slight imperfections in the geometry of the Kossel Pro, the Z-probe could move relative to the print head, leading to problems with bed calibration. This endstop screw mount is designed to solve that problem. Simply mount it on top...
thingiverse
see the older version 3: http://www.thingiverse.com/thing:1765913 Parts List: E3d V6 Hotend 3x 30x30x10mm fans 24V or 12V depending on your printer 6x #4 5/8" thread rolling screws for plastic (amazon) 3x #4 3/8" thread rolling screws for plastic...
thingiverse
Print Settings Printer: Kossel Pro Rafts: No Supports: No Resolution: .15 Infill: 30% Notes: I printed this at .25mm layer height in Gunmetal and Translucent Red PETG, and it turned out awesome, the design simply slides together, no screws...
thingiverse
This is version 8 of my end effector for the openbeam kossel pro and other delta printers. It uses an E3D V6 and has fantastic part cooling. Main goals for this end effector: -fit an e3d v6 -avoid nozzle from getting too far beneath arms ...
pinshape
SummaryThis fan mount can be slid up and down the vertical extrusion and the fan can be tilted to direct the airflow where needed. It was designed for the 'Fractal R2 80mm' fan but could be modified for others. ...The source files are there as well as...
thingiverse
This fan mount can be slid up and down the vertical extrusion and the fan can be tilted to direct the airflow where needed. It was designed for the 'Fractal R2 80mm' fan but could be modified for others. ... The source files are there as well as STEP...