laser head mount 3d models
483258 3d models found related to laser head mount.thingiverse
Long story short, this is a mount that sits on the X-carriage to allow you to mount a laser for engraving. The laser used was 500mw from a Neje unit, set at 100mm focal distance. In use I raise the z height by 60mm, plus the thickness of the item...
thingiverse
This is a very simple but effective laser mounting guide plate for the Anycubic Pro. remove the original clamp and check that the alignmemt of the magnets are central on each of the four screws. I've only just stated in the 3D printing "verse"...
youmagine
Just keep in mind that the optimal distance from the mirror to the mount block should be around 2mm.This design has been tested on a 100 Watt CO2 Reci Laser tube, with no major problems. The laser was well aligned beforehand. YMMV. I would recommend...
thingiverse
There you can find the head https://www.ebay.de/itm/CO2-Laser-Kopf-Set-f%C3%BCr-2030-4060-K40-Lasergravur-Schneidemaschine/123124592486 Redline Filament used
thingiverse
** Required: * screws that match the base of the head * some skill at laser cutter mirror alignment * you may also want to drill out the laser opening at the bottom to 4mm; 2mm is too hard to align. * you may need to measure your existing head mount...
thingiverse
I love this laser head, I always need to change the focal length depending on the material I'm using. So this saves a lot of time. I've bought 2 pieces of line laser (9mm and without focus) It shows the point of the laser where the two lines cross.
thingiverse
Mount to use the Cloudray K-series laser head on my k40 laser cutting machine. Sorry, I didn't set the units correctly. You will need to reduce the stl file needs to 10% when slicing. I sldo included the Fusion360 partfile for remixing. This...
thingiverse
Designed for a K40 laser cutter to adapt the Cloudray head. ... The Cloudray head is 7mm higher than the original K40 head.
thingiverse
The original one was to tight to allow adjustment without having to take the head off, I basically redrew to make it easier to adjust with head-mounted on, I also added a screw hole for a laser dot attachment. EDIT: I also included a V2 version that...
thingiverse
This mount provides a way to tie down the wires going to the laser and motor on the laser head. Halfway through the first engraving I saw that the wires would soon break off, at the connectors, from all the movement. ... It's designed for the widely...
cults3d
This mount provides a way to tie down the wires going to the laser and motor on the laser head. Halfway through the first engraving I saw that the wires would soon break off, at the connectors, from all the movement. ... It's designed for the widely...
thingiverse
I have included the files for the fan, laser, drag chain and mounts, 12mm ball joints and the Mini Top. The files are all original except for the chain links. For that I borrowed heavily from another design that I liked. Its from a drag chain...
thingiverse
Laser Head Mount Install ------------------------ I used ITGuruWoo's laser head mount as a base as it allows the use of the pre-installed OMTech drag chain. I made the following changes to the design: • Made the mount more narrow. • Moved the rear...
thingiverse
Here is my mod of the Cloudray K Series CO2 Laser Head mount by tibuck. In order to adjust the laser ray properly, the cloudray head had to be closer to the X rail . Once printed, fix the head on the holder. Bold the two parts together, don't...
thingiverse
Video of it in action here (it is the green part):http://youtu.be/on1uARh9xOU The laser head I am using is this one: http://lightobject.com/1820mm-Laser-head-w-air-assisted-Ideal-for-K40-machine-P701.aspx Special thanks to TrevM for making the really...
thingiverse
Remix of hhttps://www.thingiverse.com/thing:4067385 That is a Remix of https://www.thingiverse.com/thing:3061893 - Air Assist Tube Holder + Drag Chain (that carries air assist and laser power) Allows for the fitting of a Cloudray K40 12mm Head to...
thingiverse
This is the svg of the laser cut files for my Head Mounted display on instructables:http://www.instructables.com/id/DIY-Head-Mounted-Display/
thingiverse
Infill: 100% Auflösung 0,3 Geschwindigkeit: 60mm/s (Anycubic Vyper) ___________________________________________________________ Hello, this is a holder for the laser head of a DIY (China) laser. ... Infill: 100% resolution 0,3 Speed: 60mm/s...
thingiverse
Only do a couple of mods for use on my CO2 Laser head Thanks !
thingiverse
Made some attatchemts that fits the M4 screws that came with the snapmaker to be able to quickly hand tighten them to the CNC/Laser bed. Also some mounts that can be scewed down in multiple directions. ... Tip if you want updates or modifications
thingiverse
... cutouts for hex head screws and nuts to the bigger clamp. ... There is a small test body for the cutouts. You can change the cutout size in the fusion360 file. It's a parameter. Added a spacer for the mount, to increase the height of the laser tube.
cults3d
... cutouts for hex head screws and nuts to the bigger clamp. ...There is a small test body for the cutouts. You can change the cutout size in the fusion360 file. It's a parameter. Added a spacer for the mount, to increase the height of the laser tube.
thingiverse
Laser mounting sleeves for 33 or 40mm Laser heads in 52, 65 and 69mm Motor Mounts.A mounting sleeve to allow a 33mm square Laser head to be mounted in a 52mm diameter motor mount on a CNC router.
thingiverse
I ordered dual lasers for my K40 Engraver and didn't like the mounts they came with, so I created my own. ...I angled them in such a way, so that if you have a 50.8MM focus point lens, the 2 lines on the laser will meet and form a point at the correct...
thingiverse
This is a mount for on top of laser head to accept a long bolt mount for a drag chain on K40 Laser made from 3mm cast acrylic 14% power, 6-7 ma, 300 mm/sec for Raster Engrave. 16% power, 7-8 ma, 300mm/sec. ...Vector Cut.
thingiverse
This is a simple mount that allows to use the Ender-3 S1 Laser module without remonving the Sprite extruder. ... https://youtu.be/-a9nY-8EYfI
thingiverse
I modified this to fit the 10w laser on one side. ... Remixed from https://www.thingiverse.com/thing:5265453
thingiverse
Bumper guard for the Xtool 40w laser head Mounts on the forward right and left corners to protect laser head from striking the frame rails 1mm thick with clip-on attachment; does not interfere with magnetic plastic vision guard