laser pointer holder 3d models

NB: Designs added for arms with reinforced mount ends (eliminates any "flex" when performing heavy maneuvers) and beefed up the battery holder parts a bit – haven't had any issues with originals but I know not everyone lands as carefully as I tend...

I added a 120mm top mount fan holder. I have had better luck with my setup by having a fan on top of the modem pulling air through than blowing from the bottom. So, I threw this together to hold a 120mm fan. You should be able to use fan screws...

If you've printed the keyboard holder without the keyboard in it, there will be a few small ones in the front/top of that piece. Also on my printer, I need to clip a small disk that forms when the lid is started. If the disk isn't clipped off, the...

The 8 mm rod must sit tight in the vertical holder, the VertikalHalter16x8 fits on a 16 mm rod / tube. VertikalHalter0Z5x8 fits a 1/2" water pipe. Tail fin Tie, TieInter, heart, 120, 130 und 140 are glued to the respective carrier with CA. For...

There are also holes in the top for integrated cup/pen holders with a 3D-printed translucent sleeve and light strip channel so they light up too :-D I used birch butcher block. I tried some dark stains, but I found that the light birch did not take...

Then a new filament spool holder was fabricated and mounted on the outside of the cabinet. See Thingy - 780379 The X-axis hot end extruder and Bowden setup was broken down to eight parts to print: 1). X-axis extruder mounting plate (mounts on the...

You will need: - 3 batteries Li-Ion 18650 - 1 fan : https://fr.aliexpress.com/item/1005003098017287.html?spm=a2g0o.order_list.0.0.3c605e5bUydQEI&gatewayAdapt=glo2fra - 1 Activated carbon filter (to be cut to 80x80mm):...

This was a much easier when I had a hex hole that fit an allen key, with the new spring holder and internal latch, not so. One trick which may help is supporting the center gears with a piece of 25mm dowel and giving it a few taps from the other end...

This is to ensure the tray does not slide around and to provide the proper 6mm offset from the front so the lid of the center console closes without force or the need to adjust the tray each time. This design also takes the tissue box holder into...

the axel and bearing's inner roller must form a fixed subassemby, and the outer roller of the bearing is simply held in place by the holder's geometry (has it has a rim on the outside, so once assembled the bearings physically can't come out) I'd...

3TSS: 30mm Tube Spool System This is a complete solution to convert a regular 30mm tube into a horizontal/vertical (suspended!) spool holder for one or more rolls. It includes: Fixed spool hub adapter Axial bearing spool adapter using 6mm softair...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

- It has probe holders at the back plus it keeps the cables tidy and tucked away in the "Cable Eater" at the front, keeping your bench a bit neater. - It has a basic capacitor discharge station (holds a resistor of your choice) - An LED tester...

Install the PINDA probe into its holder with the wire looped on the inside of the probe as directed by Prusa. Push the remaining coolant line through its hole in the x-carriage below the lower bolt and loop it around between the fan and extruder to...

Note: The X axis part is for the current model of the Geeetech I3 Pro printer that uses a metal plate on the X axis to support the linear bearings and extruder holder. When I was assembling my Geeetech I3 Pro C printer, I was struck by the fact...

We can then use a simple Cube object to create a cut in the face for the pivot (holder) for this target face. The resulting cut will allow us to build an arm to hold up the face and pivot from the base. You can use the techniques as described in...

Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work. Our puzzles are modeled using the open-source...

For the cooling system, also download one of the cooling designs mentioned here, or use the basic E3D V6 fan holder for the heatsink if you don't need or want a part cooler. This is designed for a Folgertech FT-5, but might work on other printers...

The supports should be printed at 0.2mm layer height to maintain a one layer gap between the support and model. STEP file is included for easy remixing. Thanks to TotalRetribution for the model of the TS-80 which I used in the pic to show how the...

In this case those on the plate have been used.The used drag chain bridge that has been used is the following (buy two...

The 4 larger holes on the very top of the main case body are for heat-set inserts; the 4 larger holes on the face of the main case body, where the PSU holder mates with it, are for heat-set inserts; and the 4 larger holes on the lid that the fan...

160,3mm the ring up and bottom is approx 162,5 and the thing is approx 183mm high https://www.amazon.de/gp/product/B08S45Q76M/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1 - 4 pieces - 608zz "Skateboard" Bearings (or use 608RS and lubricate...

The frame side parts - tool holders, limits etc. are here: https://www.thingiverse.com/thing:5150890 An overview of the end result here: https://www.youtube.com/watch?v=x-ut81sn-io I will be posting another video detailing all the conversion...

Accepts a battery up to 7mm thick with the S back or 18mm with the X back.Nuts: Uses M3x2.4mm nuts and M3x8mm screws to hold the back on.Inserts: Uses M3x5mm heat set inserts and M3x8mm screws to hold the back on.TBall: Has a cover over the center...

...Now press the earpiece holder dowel end into the hole in the pipe and press it to fit. The earpiece hangs on this fairly easily. Should be all done. Everything should have been test-fit before final assembly, so you should know how everything goes.

It allows them to have easy access to everything they need from writing utensils and essentials such as sticky notes, paperclips, USBS, erasers, and anything that can fit in the cabinet or pencil/marker holder. It organizes students’ desks so they...

For the cooling system, also download one of the cooling designs mentioned here, or use the basic E3D V6 fan holder for the heatsink if you don't need or want a part cooler. This was designed for a Folgertech FT-5, but might work on other printers...

So prepare/buy 2 pcs in advance.You will not find any cable holder part on the printhead. Not because of lazyness, I just wanted to avoid some unpredictable shaky things on the printhead. I cabletied everything to the 20mm air tube. Not pretty, but...

The other two files have been included in case someone wants to shift the position of the extruder holder or, has another idea in how to modify this setup. INSTRUCTIONS (Follow These Instructions To Install) This is installed the same way as...

The holder is 120mm high, that worked for me and my drawer but is customizable. ## buttonBattery This is a small tile to hold 357 style of button batteries. ## cabeHolders Intended to hold 2 USB or other smaller cables. 120mm tall. Similar to...