last of us clicker 3d model

I uploaded the 3 parts so if you have a different holster you just have to customize one of the parts. The first print was done completely in PLA (which isn't good for sunny days). I am printing another one in ABS, just ran into some issues while...

The Axle Distance is Increased by 10mm Due to Lack of Room in the Chassis. Maybe There Will Be a Future Chassis Design That Matches the Original 145mm, Stay Tuned for Updates. There is No Additional Hardware Needed Except Spur and Pinion. Well,...

The 9th hole is for the chassis ground of the connector should you require it. It should not matter what 4mm Banana sockets you use, providing they have an 8mm mounting hole. I have a link the ones I use: ...

I repurposed a couple of old skateboard bearings my son had lying around for the shaft supports. The shaft is an 8Mx80mm hex bolt. (there is a parts list in the pdf file)</p> <p>This uses the hub_short.stl from the original thing and only requires 3...

https://github.com/FLSun3dp/FLSun-Kossel-Mini/wiki/02.-Calibrate-your-printer I leveled my printer using z-prove on the effector, with an offset of -0.1mm. I also added a calibration spiral and scaled it for printing. Important note: My firmware...

I used RC boat prop shafts and housing as axles this time, with a M3 thread rod and a propeller drive dog on top of the assembly. The Handle wheel stand gets glued onto this dog. You'll need a 6mm drill bit stopper as a collet to lock the wheel...

A new version of JaredNew's creation (http://www.thingiverse.com/thing:59403) has been developed to fit my original note perfectly. To personalize the mount provided by JaredNew, check out his work at http://www.thingiverse.com/thing:59403, which I...

Version 2.0 modify the design of the aluminum block bracket to maximize cooling, so that you can use the bmg screw holes. To mount the bracket all you need are M3x50mm screws, I could not find but make custom screws with an M3 threaded rod, and for...

Match the text color of the size tile to the Revo nozzle sock, etc!NOTE: The tile tolerance is extremely tight! This is to prevent the tiles from vibrating while the printer is in operation. If the tiles are TOO tight, you can scale them down in your...

The provided g-code has little support for printing with PLA, which is easy to remove.When you print with PETG you may aslo need according to user experience some support for the overhang of the knob.================Das Original von Koray ist clever...

My goal is to minimize the weight of the X-carriage while adding cooling for PLA. To achieve this, I created a Bowden setup and installed two "snail house fans" on the X-carriage. I also removed the cable holder and connected the cables directly to...

A 1000 µF capacitor, charged through a diode, may be used to separate the powersupply of the NE555 from the DC line to stabilise the powersupply and keep the LED on if the USB charger does not have sufficient power to keep up the voltage during...

Turn both valves clockwise to ensure a complete shutdown of the water supply. Next, disconnect the water supply lines from the faucet by loosening the nuts that hold them in place using an adjustable wrench. Be careful not to strip any threads...

I need to verify the location of this crucial component. Timing belt, approximately 1380mm with a 5mm pitch: These should fit, but dimensions may vary depending on the bike. Check out these options:...

For each of the clamp designs, one has "H" and "C" to identify Hot and Cold and the other does not. Both designs isolate the PEX tubing from framing and include nubs (technical term) to help keep the pipes silent as they expand and contract.</p>...

The diameter of the propeller is more like 184 mm, so this guard inner diameter is 188 mm. You may swap between the Propeller Guard and the Motor Stabilizer as the height to the wing mount is the same for these two parts. Dont mount the black fan...

Customized version of http://www.thingiverse.com/thing:813330 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: no_hooks = false 58point5width = 58.55...

This is based of an ingame item from Minecraft Dungeons, created as "Fan Art", No infringement intended. <p> </div> <div id="tip"><h5>Dont forget to leave a Like or Comment or even <a...

I don't know the connector type for the fan so I cut one off of a spare Cetus Extruder to plug into the Extruder Distribution PCB. I added a 4 pin jst-xh connector to the Hemera stepper motor harness to match the Cetus stepper motor receptacle on the...

Remember to print three of the aircraft units. To connect the aircraft units to the base you will need a straight paper clip.</p><p>The ships stats are in the downloads section</p><p>The rules to the game are in the downloads section</p><p>Bismarck,...

... for SLA resin printer <a href="https://shop.prusa3d.com/52-original-prusa-sl1">Original Prusa SL1</a></p> <p>Use Prusa though resin. ...Be careful when you remove print from platform because there will be still some amount of resin inside the print.

Hi, to download handle for an automatic refill for two water lewel sensor, dimensions given in the pictures i add versions for 5mm, 6mm, 8mm, 10mm thick glass.To build an automatic refill straight from the RODI system you...

... The hole that matches the tower should be widened, or oval shape to allow movement of the rod side to side. There are two towers Sr, and Jr. The Jr. tower is used for most projects. The Sr. tower is for using the pusher with a 2x4 framed matrix.

I printed everything at 0.16mm resolution, of course, lower is better, especially for moon-top but expect a 24h+ print time. You can print moon-base.stl without supports, moon-wheel needs a little support under the gearing, moon-top needs support...

I will print the bottom printed normally to check if needs waterproofing if it also needs spray to waterproof, I may make another version with 4 walls to see if it I doesn't need extra water proofing then Edit: 3/6/21 Uploading the finale versions of...

The design of this plate will allow most any cable carrier to fit, as it's a simple plate mount. I have a version with and without holes, so you can create your own holes as needed. I also checked the fit for the IE version on my CAD software and...

RGB LED race gate for indoor FPV micro quadrotors (tiny whoops). Update: I've added wall mount swivels, so you can mount your gates on the wall, and they rotate up against the wall out of the way when not being used. Built with: 2 90-degree elbows 2...

Customized version of [http://www.thingiverse.com/thing:184196](http://www.thingiverse.com/thing:184196) created with Customizer! ... Using the following options: Outline = Circle My Y = 0 My X = 0 Use Image = Yes Use Drawing = No My Image Y = 0 My...

make sure the cable is going in the direction as shown in blue:Insert a 28mm piece of PTFE tube into the Rapido (red), and screw in the Orbiter (2x M3*10mm, blue): Mount the 5015 fans (4x M4*18) and BLTouch (2x M3*10 + 2x M3 nuts) with the screws as...

This is a temporary &amp; emergency Contact Display Card which shares you contact information with people in an unknown area so that they can contact you for anything related to your car.There are 3 versions of this Emergency Contact Display Card :10...