latch mechanism 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 3 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

I made a small update to it, adding the model with the included screw threads in the back, and ever since that update the thing is still there but returns a 404 error for everyone who isn't me. I've tried to get it to post, I contacted thingiverse...

... control the LEDS with preset printer events such as warming, printing progress, error, cooling, etc. https://plugins.octoprint.org/plugins/wled/ Original design remixed from K2DesignLab: https://www.printables.com/model/174959-makerdeck-logo

For example, if you shower pole diameter measures 22mm, try a Pole_Diameter value of '21'. Material We recommend printing this holder in ABS filament for extra durability. Versions 1.0 (5 Dec 2020) - Initial version Printing Recommended slicer...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

Many thanks to Dalek_Kolt for providing the original model, you can find more ripped stuff from them here: https://www.vg-resource.com/thread-39778.htmlDisclaimer:The figure you see in the photos is a larger version that houses LEDs and batteries. If...

... glad to finally get this published. Any questions about the historical nature of this set can be addressed to Simon at the email address above, and I will try to answer anything on modelling or future edits here in comments. ... -Ian R.

DescriptionThis is a fast and easy to print model to calibrate your new filament. It can be used to find the right settings for the extrusion factor to get the right wall thickness.</p><p>It is designed with a 0.86 mm wall thickness to meet the...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

remixed from the great work from https://www.thingiverse.com/thing:1681442 see it move https://youtu.be/rTlbqrB86YA -- big wheel: one side glued to the axle, other side tightened with screw (drilled a 1.8mm hole and use a 2mm screw); gear on the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Helicopter Collective Controller Work in progress. 6/17/20 Added File Added collective_open v4.f3d (An assembled model of all the parts.) You can alternatively use my Russian style grip located here:...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

You Need: Raspberry Pi Model B or Plus can be purchased here. A 2-channel relay board will suffice; purchase here. Jumper cables are available here. Buy buttons here. Get a webcam from here. Acquire an SD card here. Power your Raspberry with a...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

I have designed myself some shelves for the paints I use with my Warhammer 40K and other model painting. The system is designed so you can put a shelf on both sides of a wall and chain them together. For instance, you can do a 2-step wall, shelves,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Refer to the pin diagram below.Connect the SMPS OUT- to a ground pin on the RPi.If you're using the fan, install it on the lid.Connect the fan's power and ground wires to pins on the RPi. My 5v fan was a little on the loud side so I used 3.3v and...

Enjoy :) Update 04-05-2021: Adding ender 6 models, upgrading all to V4.3 (slotted mount holes for 2mm height adjustability) and adding "fan duct up V2" which has integrated grill. It's more tricky to print because of the small features so i'll leave...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Some model are not there, you can find more here: https://www.cgtrader.com/M600 Instructions I printed mine on a Leapfrog Creatr with ABS (240°) and a bed at 100°. Settings used have been: 0.35mm layer height 2 perimeters 4/4 solid layers...

This is the first 3-D model I have built from scratch and I was looking to get it done quickly. So, I kept it simple but did note that it wouldn't take much to add a few more amenities that would suit personal needs or desires. The router fits...

I have the model assembled if anyone is interested; just can't upload a .step file (check the comments for it now). Keep in mind that you may need a shim (flat washer) to fix any misalignment issues with the Creality Heatsink. I've used this...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...

A perfect fit for your specifications, this model features the following options: picture =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

There is a tight-thread version of all the models for those wanting a tighter fit or using a resin printer. Caps Flat Cap Flat Cap with GB Logo Cap with 3/4" Loom Stub Cap with 3/4" Loom Stub and Circuit Passthrough Cap with GX-20 Geometry Cap with...