line integral mathematica 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

It's also recommended to use a couple of the filament guides to keep the filament feeding along the line of the cable - see http://www.thingiverse.com/thing:746048 for a suitable part. All the parts are sized to be printable on the M3D Micro,...

I used prusa slicer for this and it worked well in my favor to keep print times down, but print strength high. Post-PrintingStep 1: Joining surface sanding After printing everything, start by sanding all the joining edges to a flat, rough finish...

Don't worry about that right now. Slide the stabilizer fin into the slot in the rear - narrow end forward and two lines on top - making sure that it goes through the grip and out the slot on the other side. You will need to make sure that once the...

And all the electronics will cost about $7. Depending on the firmware, you can use as a clock, lamp, creeping line, night light or color music. The design does not use filling, but only walls, so printing is relatively fast and low material...

If you can, print them onto a really smooth buildplate such as glass or steel etc to cut down on visible print lines. If this isn't available on your printer, then I recommend using "ironing" in your slicer of choice. 3) THE BLUE LENSES: There...

Change the code (starting from line 72) to activate the circuit ONLY if connected to PA3. Do not use this code snippet without the circuit. -End of update 27 oct. 2020 Some typical values in attachment. Do not attempt to measure AC voltage...

Thanks to the repair contest I finally got my act together to repair it with a printed part.When I presented the repair to my wife, I expected an enthusiastic response (along the lines of "Wow, marvelous, what a repair hero! Hubby did it again!!"). I...

 Wrap some masking tape around roughly where you want to make the cut - this will make it easier to mark, and will help to keep the edge a little stiffer when you are cutting it.Find an object that's about the height of where you want to cut,...

I've commented out a lot of serial debugging lines that can be uncommented if needed.The program has a switch debounce routine that was necessary for it to work at all.The '#define BIT_DEBOUNCE_COUNT 8' at the top defines how many times the switch...

From the arduino, the data line of the LED strip should connect to pin 12. For the DIP switch, one pin of each switch should be connected to arduino pins 2 through 9. The other pin should be connected to ground and +5v as is standard for buttons on...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

Line the nylon shaft of the gear motor up with the corresponding notch in the 3D printed shaft, and push M3 nuts into the lower hexagonal spaces in the bearing housing. Push the 30mm M3 screws through the holes in the gear motor, through the holes in...

Print in PLA (or ABS, PETG...) at 0.28 mm resolution and (around) 20% infill (I use lines). I once again printed the main body in this <a href="https://s.click.aliexpress.com/e/_99SlSf">Carbon PLA (- not so much because it is stronger, rather...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Also you can have a second column, opening to the right side of the tag.I opted for 80mm line lengths for all of my tags, because it seems to be long enough for most purposes and also is short enough for the tray not to become too flimsy.Happy...

Note I didn't bother with the black stripe around the side as it would be really hard to put on smoothly since the line would be like 0.3mm or so at that scale.Charge Rackone of the major advantages of NATO artillery systems is their logistics for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

(to prevent IR LEDs reflection)Step1: Make the Base section.Open the "Unifi G3 Instant_Case_Base" STL file in Cura.Set the Infill Density to 100% (for best water-resistance).No supports are required for this part.Slice it and in "Preview mode" make a...

However, some patterns (such as 'Hole', 'Lines' and 'Hearts') may not print on vertical surfaces without supports.Following feedback that some users had issues stacking the caddies, the default Lip_Gap size has been increased to 0.6mm in version 1.4....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Measure down from the top lip ~12.5" [315mm], this should be the dead middle of the last bump indent prior to the square hole.&nbsp;Cut out your front face outline to form the ‘Lid’, this is the middle shelf.&nbsp;Note 1: Use your box cutter to score...

Print the first layers in white and the following layers in another color.&nbsp;UseOnce printed, put a Tesa PowerStrip onto the base and stick it on a surface.Other modelsAlso have a look at all my customizable creations.&nbsp;There are more...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Single Line Bangles - Stand out from the crowd as you wear one of our classic single line bangles that speak for themselves. Mangalsutra Bracelets - Weave magic into your attire with our enchanting Mangalsutra bracelets, paying homage to cultural...

This turned out to be something of a blessing, since it also turned out that my preassembled screens weren't mounted squarely, so even if the hole was the correct size, it wouldn't have lined up correctly with my screen. I ordered my boards...