link n64 model

Make your own among us angel, with a luminous halo!Light up the dark with a mysterious impostor or crewmate.What do you need?3D printer :)White and coloured filamentSoldering iron, solder and 3x 18cm wireDigital RGB LED ring, 12 leds (OD: 52mm | ID:...

The most common ones used for model rockets were very pricey and hard to find in bulk. I did some research online and found a couple of people having success with pencil graphite, so I started experimenting using an 18V drill battery as my power...

Parts description This printable model is made of 4 parts: Casing: this is the central part, the thick ring with a partially-closed wall on one side. Inner ring: a thin ring used as part of the locking mechanism for the petals. This part must be...

Click the “like” button and show your support. If you find this model useful, feel free to buy me a coffee. Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy.In one of the pictures, you can see a side by side...

It is intended to be loosely attached, for quick removal during total eclipse photography, and as a result, may not remain well attached in a windy or gusty environment.Materials neededPLA or another rigid filament for the frame pieces.Flexible...

Some overhang areas in the inside don't bridge well, so you'll need to do some trimming / post-processing.Updated 5/2/2021:I added aluminum foil tape (HVAC duct tape, buy at any home/hardware store) for 3 reasons:serve as heat spreader so that the...

The text holder and book pages slot into the cover pretty easily.Use some double-sided tape to affix the book in the center of the mirror, slightly towards the back, with the spine and letters facing you.The rest is self-explanatory, put the paper...

*Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit.* **UPDATES** **V3.3** (slight comfort improvements over v3.2). [print 1 for each eye] **Added a version for the prescription inserts from VR Lens...

... 3D model created using SketchUp Make (free software). I also tried 45 degrees, but the fan's thickness made it touch the desk surface below, so it had to be skooted up to the high end of the stand... thus the cooling effect would be diminished.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 6 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

The SATA power cables were custom made, from a stock Molex to SATA power cable cut down to 10cm and re-terminated with the 4 pin 2.54mm pitch JST XT connectors which the Odroid H2 has on board.SourceSource FreeCAD models:...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Please check the images to see what it is included in this kit.This set contains: - Jadeshell Turtlekins (6 + 6)- Giant Snails Riders (4 + 4 + 4)- Giant Snails (4)- Tokun – The Travelling Merchant- Tso'ok Raging Wrath- Yatl – Jadeshell Beauty...

I found when doing this I had to clean my hotend and its was really difficult with this model. ... I included my wires for my NEMA17, but I can tell you right now, your NEMA17 will not be the same, you will have to figure out your pinout by yourself,...

The COMPLETE Thieves Guild bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Thieves Guild AdeptsVery little is known about the legendary Thieves' Guild in...

Also im not responsible for any damage your printer takes while printing this files. That said, i fixed anything on this model, and it is very much printable as is, you just may have to add holes for your hardware manually, or take the f3d-file and...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

A short bridge is required for the rail end caps. Post-Printing All holes are intentionally modeled as very tight fits and are intended to be drilled out with a 3mm bit to ensure proper fit. The threaded inserts will push waste material into the...

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 0 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

It can print without support, and if you have the workflow dialed in, it takes only about 30min per label from start to finish. You might get away with printing just the modell without the support stuff…. didn't try. Depending on your bridging it...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

Enjoy my Ulvheim Small Merchant House. It came from my Patreon February Release. Thanks to all my supporters and to Markus Kruse / Terrain4Print, creator of the Ulvheim City. This model is supportless as usual. :)</p> <p>Discover my Ulvheim Remixes...

 The cable was routed to the reoriented Z axis Cable Chain and routed through the new Z axis belt cover on the right side of the printer to the U2C USB to CAN adapter,Finally, the U2C adapter was connected to a freed USB port on the RPi.Fusion 360...

Also also: if you get sick of chasing dice when they fire out of the bottom of the dice tower at high speed and scatter over the edge of the table, I would suggest you head over to [**domino6713's dice tower courtyard...

The gcode files here are not 3d models being printed, instead they're for people either diagnosing their machine, or their setup. IMPORTANT: READ THE PRINT INSTRUCTIONS. These test codes are for diagnosing and finding vibrations, noises, etc on the X...

It will not fit a full sized stepper, use their model if you have the original stepper motor. I suggest printing with the end that hooks over the carriage on the bed with supports on bed only. There are minimal supports this way and the hook keeps...

It can be printed entirely in PLA but we prefer to do the extruder and X-axis parts in ABS.\nHow I Designed This\nThis design uses many of the same spacing and remixes parts from the Printrbot Play...