lna4all 3d models
19 3d models found related to lna4all.thingiverse
This is the LNA4all case for use with battery. Edited with larger hole for switch. ... This is BETA
thingiverse
A mounting block for the LNA4ALL board. ... There is a notch for the power input holes and a trough to accomodate both the sma connectors and possibly a zip tie for mounting.
thingiverse
This is a case which is housing one LNA4ALL and one LNA4HF low noise amp for the us with a RTL-SDR USB stick. ...More details on my blog:http://diebastelkammer.wordpress.com/ Instructions The details...
thingiverse
More about the design and this little project can be found on my blog here:http://diebastelkammer.wordpress.com/2014/11/17/lna-transportables-case-mit-batteriefach-fur-lna4all/ Instructions You need for a rebuild the following parts: 3 printed parts...
thingiverse
Custom-made enclosure for a LNA4ALL Low Noise Antenna Amplifier (http://lna4all.blogspot.com). Note this is NOT a radioelectric proof case, it is just a mechanical protective box to preserve the electronics. It is made in two pieces: base and lid. ... ...
youmagine
Custom-made enclosure for a LNA4ALL Low Noise Antenna Amplifier (http://lna4all.blogspot.com). Note this is NOT a radioelectric proof case, it is just a mechanical protective box to preserve the electronics. It is made in two pieces: base and lid.
thingiverse
Housing for the LNA4ALL, with room for a power plug, and optional filter capacitor and/or rectifier. Need 4x M3 nuts and 10mm long bolts for mounting. Print Settings Printer Brand: Solidoodle ...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/1uSdOefdfui
thingiverse
I consider it a work in progress because I have not even powered-up the LNA4All yet, so don't know if it generates heat, for example, that might demand some cooling holes or other mods to the case. I'll figure that out as I go along. The LNA4All...
thingiverse
... snapped away from its neighbours after the manufacturing stage - there can be small sticky out bits which can be carefully filed away. I have removed the slot for power leads in the original as I power my LNA4ALL using Bias-T from my SDR dongle.
thingiverse
... Fix 35mm mast antenna Fill 40% min Alu Tube 16mm N Female base conector N Male RG58 Cable or equivalent. ... Terminals. LNA Pre-Amp recommended. Reference: http://lna4all.blogspot.com/2017/02/diy-137-mhz-wx-sat-v-dipole-antenna.html
thingiverse
... at big box hardware stores or on Amazon. The antenna fits in the camera shoe mount for a tripod. Picture: https://i.imgur.com/jRLRpMU.jpg For construction details see: https://lna4all.blogspot.com/2017/02/diy-137-mhz-wx-sat-v-dipole-antenna.html
thingiverse
... a lot of smal 8x3mm magnets. Remove the brass pice from the orginal antenna and put in the top of the new one. If you want to improve prefomace of the antenna there is room for a LNA4ALL LNA pe picture. modify the open scad file if you want. ...
thingiverse
Bracket for a 137 MHz V-dipole antenna following the design [found here](https://lna4all.blogspot.com/2017/02/diy-137-mhz-wx-sat-v-dipole-antenna.html). I modified the design slightly by removing the screw terminal and mounting solid core copper...
thingiverse
Basic construction of the dipole is described by Adam-9A4QV in his blog, here http://lna4all.blogspot.co.uk/2017/02/diy-137-mhz-wx-sat-v-dipole-antenna.html What I required was some sort of mounting arrangement so that I could fix the dipole to a...
thingiverse
... (low noise amplifier) with ham radios to improve performance. For examplehttp://lna4all.blogspot.co.at/2013/04/lna-for-all-low-noise-amplifier-for.html Print Settings Rafts: No Supports: No Resolution: 0.3 for bottom, used 0.14 for top Infill: 15%
thingiverse
• Electrical resistivity & conductivity -- https://en.wikipedia.org/wiki/Electrical_resistivity_and_conductivity • Unity Gain Opamp -- http://www.learningaboutelectronics.com/Articles/Unity-gain-buffer • Bias T --...