low poly character 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale] Once a renowned mercenary and officer within the Golden Griffins, Lydia spilt rivers of blood during her time among them on the front lines of the Liturium War. When...

These two parts are rather small but also simple ball joint parts that rely on friction and cannot be tightened. For those of you that want a to be able to tightly secure your camera in a certain position, there are also parts that form a double-ball...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 20 stencil_pattern_element_shape = 3...

Printer Settings: * Printer Brand: RepRap * Printer Model: Original Prusa i3 * Rafts: No * Supports: No * Resolution: 0.2mm * Infill Percentage: 25% Print Notes: I utilized a 0.8mm nozzle to expedite the printing process, which took approximately...

I considered adjusting the model but decided to leave it as is, as I'd rather have a more positive engagement that you can adjust to your liking than end up with one that doesn't latch in place securely enough. I'll leave this marked as a work in...

This thing is a two-part shield for the head of your Ryobi trimmer, model number: RY40220. It’s a bit crude, and I planned on making it look smoother, but this thing really works! By narrowing the gap that the grass can fit through and diverting it...

I'm not sure how common this exact failure is but I figured I'd share it in case it helps someone from throwing out their cover and having to shell out for a replacement. There are other repair pieces for Audi/VW cargo covers which are used on wagon...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   A vanguard of the Duke’s Army that was initially sent to quell the outbreak. A thousand men were torn apart within an hour of arriving in Canos’ south side, leaving...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   Once a member of the elusive Psithars, Bastian abandoned their order over their methodology and views on non-humans. He moved to the University of Canos, wishing to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

I simply used a couple of dabs of model car glue, but you can use epoxy if you prefer. I would avoid CA because the fumes may fog up the inside of the lens. The finished part is shown in "modified camera.jpg." I just checked Amazon and found that I...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...

... mount and two each side for accessory mounts. I used one on the right for strain relief for E3D wires, 2 on left for fan mount. 4 on side fan, only two are used depending on fan model. ...2 on cable chain attachment to attach it to extruder mount.

http://www.thingiverse.com/apps/customizer/run?thing_id=406494 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

If you are looking for more, check out our premium projects: https://codeandmake.com/premium OpenSCAD Customizer Options You can customize everything from the size of your cards, to the number of decks it will hold and you can even create a...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

... most of these parts. If there are any tweaks necessary let me know. I have added a .step file of the assembled printer and I will upload a Fusion 360 back up file as soon as its processed so you guys can go nuts customizing the solid models.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   One of the twin daughters of His Excellency High Bishop Madrigal, Speaker of Erdrydion. Amélie’s life has been spent entirely within the church, though in a very...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Using the paint supports tool in PrusaSlicer, put supports around the square cutout that you can see by looking through the bottom of the model. Look at the image below for reference.</p><figure class="image image-style-align-center image_resized"...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...