lying down person 3d models

The bearing's basic design remains the same as previous versions, with a structure similar to the V2 model where the cage bridges cleanly over the rollers entirely (I've removed the V2 design since it's now obsolete). I have added loosening slots to...

Also, added 1mm to the bottom of the model and made it where I could make it TPU for some grip. *UPDATE 21FEB2020* Uploaded Rev 4.1 Fixed a section that had a small gap in the cleat that could possibly make it a little weaker than it should be (back...

A splined connecting type is suggested for evenly distributing load on the shaft/rotor connection (modeled with key connection due to limited time). A 28V, 1080 RPM motor with a power output of 0.149 kW is required for control. Two flow control...

New version of Bondtech BMG Prusa Upgrade MK3S/MK2.5S with RHD ver.C fan shroud. I modified the original version model to be easy printable with FDM printers. The original source: https://github.com/BondtechAB/Bondtech_Prusa_i3/tree/master/CAD-Files...

This design is compatible with both the original & OLED model Nintendo Switch. Print settings: Use tree supports (on build plate only) when printing the PC case & display monitor. The files that require supports are named:...

This version is called the Plumer's Helper as it looks like Mario. The pictures above are after I has glued, covered in epoxy, sanded, primed, sanded, painted, sanded, painted, and finished in a clear coat. It took me about a week to design this in...

If you do this, be sure to have enough separation between supports & model to facilitate removal. This is true for both walls and support interface. 15% support density was plenty for mine. Other orientation may work better for you, but I wanted...

There are several affordable speed controllers on the market, and this one often comes under the name "6V-90V 15A PWM DC speed controller." I purchased my unit about six years ago, which had a blue circuit board; however, newer models typically...

... together to see which fit the best. Due to the overlapping nature of the mechanism, it helps hold the mechanism together if some parts are loose, it can also make adding the last door a bit tricky. The tolerances for the model assembly are 0.3mm.

They slide easily into the eyesockets of the model, but also slide out, so a touch of glue is required. Also needed is the pin to secure it to your clothing. Garnets: https://www.amazon.com/dp/B078M979TG/ref=cm_sw_em_r_mt_dp_U_zgQkDbBN2AK5R Pins:...

You can find the OpenSCAD source here: https://github.com/simoninns/renault-twizy-speaker-mounts ## Printing instructions The model has been printed and tested on the Prusa MK3S/MMU2S printer using Prusament PETG filament. All parts fit on a 20x20...

I made the first remix to add a little more connection between the towers to the token so that it can be printed at lower resolutions. I also added a chamfer to the top/bottom, so the outside is more rounded (and prints easier at lower...

I modified the OpenSCAD script printing the pen adaptors so that you can specify the top and bottom diameter of the adaptor module in order to model the shape of the pen better. I updated the ultra fine sharpie STL to have better dimensions. The...

However it can be used on any A1 and in theory should help keep internal temperature low and decrease risk of failure due to heat build up.Note: This is only for the A1 not for the A1 Mini, If you own a A1 Mini use this model...

... to the tab on the front of the picture frame. I Designed This Based on a foam board phone stand I created several years ago, this design has undergone multiple iterations and tweaks. The concept was sketched on my iPad and modeled using SketchUp.

  PrintVariation2 FDM: Each model split into pieces to be printed with FDM. ...      You can find more of my items at my website at www.tabletopminis.com For updates, mini painting and printing you can also follow me on: facebook:...

VoilàThis joystick grip has been inspired by the original sidestick, which is installed in Airbus airliners.Based on this original model with the agreement of the the author. Thank you to <a href="https://www.thingiverse.com/crash1983">crash1983</a>...

... operation on Outreach. With the Confederation's later advances in stealth technology and light weaponry, the Flea became a logical test platform for new prototypes. These performed well, which encouraged Earthwerks to refit several older models.

This is a replacement fork dust boot for a 1892-1983 Honda Urban Express, the NU50 and NU50M models. These fork seals are unobtainable individually as they were only sold as part of a complete front fork tube replacement, and are long since out of...

---------------------------------------------------------------------------------------------------------- Based on the idea from https://www.thingiverse.com/thing:3674756, which worked so well on my X8 SE, I have made these signal amplifiers for...

and 2.Connect as shown, and follow your switch's wiring diagram to ensure you are connected hot to hot and ground to ground.&nbsp;&nbsp;NotesI prefer the switch on the right side of my printer, so the model is oriented to print for the right side. ...If...

I’ve already developed a model with 16 x 5mm neodymium magnets which I’ve tested with iPhone 12 Pro Max (no case) and it works really well. ...However this does work if you have a 12 Mini or 12 and you use a silicone magsafe case on your iphone so I...

UPDATE Another member pointed out that my models weren't perfectly on the bed in the design, which most decent slicer programs would point out to you and/or automatically correct. So I put them on the bed and re-uploaded everything. UPDATE If you...

License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is licensed under The MIT License by Code and Make. Note: 'BSD' license has been selected as it is the closest...

To try to change and play with the model as much as possible so that the printing and assembly would be convenient and simple, but I gave up at a certain point and had to stop and settle for what I was able to do. The main changes I made: - Holes...

If you only need the adapter for a drive sled, then you can skip printing this model. The original S-10 drive screws won't work with the riser. You'll have to find some decent fitting self-tapping screws instead (not machine screws). I was just able...

Este modelo es valido para lastas de 33cl(las clásicas de toda la vida vaya) y para baldas de una altura de unos 165 mm(esta muy ajustado el model al hueco). Agradecer a ljhtom su magnifica idea y su total disposición para que sea modificada. ...

Place the model with the bottom side facing up. Then feed the two threads from the „topring“ through the two holes in the socket. At first just clamp the strings. Than you can start with the adjustment. So when the strings are slightly tightened,...

I'm really hoping to get some models printed over the weekend to show off how they look. (Woo hoo! V 0.2 out, got it done faster than I thought I would.) Print Settings Rafts: Doesn't Matter Supports: Yes Notes: So there are two ways to...

The image can be found here: https://openclipart.org/detail/94489/six-sided-dice-d6 Note: There appears to be a bug with Thingiverse for me, where the model for DT_Lid is being rendered as DT_Lid_D6_INSIDE. ...Despite this issue, I have downloaded the...