mac mini 2018 cooling 3d models
202498 3d models found related to mac mini 2018 cooling.thingiverse
Mac Mini 2018 Cooling Stand with space for a Samsung X5 SSD Drive. Require one 120mm x 25mm fan, four M4 screws for mounting of the fan. No support is needed when print. ...I use 20% fill.
thingiverse
The only needed supports are for the two screw holes. I combined this with 2x Noctua 40x20s and a single Noctua PWM Controller. Power tapped from stock 6-pin fan cable (from left to right, pin 1 is 12v & pin 3 is ground). I HIGHLY recommend using...
thingiverse
... never pass 75 degrees Celsius. Under normal operations around 30 degrees Celsius Note: Updated the model with Air vents around the base. In first version there was no gap. Cooling is now better with air flowing through and around the Mac mini.
thingiverse
A cooling stand for Mac mini (Late 2018) with a 140mm friction fan mount. You may want to print the top_test.stl first to calibrate your 3D printer. The plastic bottom cover should be removed from your Mac mini. ... My Mac mini with i7-8700B has...
thingiverse
My 2018 mac mini is great, but the airflow isn't great. ...I threw this together to lift it off my desk a bit, and it seems to be helping.
grabcad
Again two cases for Mac mini, oneI already uploaded. but this one is without the Mac mini mockup. The other is a square case. I have forgotten to mention that I did design this to learn Fusion 360. ...It';s not a model which is ment to be printed...
grabcad
Model of Apple's updated Mac Mini design (limited internals). This was drawn from Apple's product page, and is not intended for engineering or other high-precision applications. ...Just a rough sketch of the real thing.
thingiverse
I recently received a Mac Mini that had the fan port ripped off of the motherboard. I did not want to pay a lot to replace the board so I made this. I removed the bottom of the Mini and have secured a 140mm fan under the chassis. This stand is...
thingiverse
This is a two part cooling system for Mac Minis using 140mm fans. The top and bottom can be stacked together or used separately. In my testing the top fan doesn't dramatically change the temperature of the CPU but dramatically reduces the temperature...
thingiverse
My Mac Mini (2011) was overheating so a designed a base to give it airflow. This base can be made in two prints on a 6"x6" bed. The surface area supporting the Mac does not change, and the center of mass is low so I do not believe it will have any...
thingiverse
I designed this modern looking stand for my Mac Mini 2018, it allows better cooling and vertical position. ...Stands very stable.
thingiverse
Simple cable organizer for the 2018 Mac Mini. Simply glue it to the desk to keep the cables from pulling out. ...(Note that no holder are in front of HDMI port)
thingiverse
Customized version of https://www.thingiverse.com/thing:107595 Made a 3 supports brackets for the Mac Mini 2018. Two supports for each side and one for the front side. ...
thingiverse
This is a bottom cover for the 2018 Mac Mini. Replacements are oddly expensive online and I was making another project that attached using the cover's system and since that's the hard part to model I figured I might as well make this cover as well. ...
prusaprinters
This Mac Mini Cooling Stand is compatible with 120mm fans. The Mac Mini's bottom plate needs to be taken off. Gravity is used to mount the Mac mini. I used a 120mm fan with temperature sensor (Artic F12 TC) and a StepUp Module (MT3608...
thingiverse
With the fan on top of the Mac Mini, the metal metal enclosure runs about 10 degrees Celsius cooler than without, as measured by iStat Menus. And that is with the lowest speed setting of the fan (500rpm, 102m³/h, 17dB). Only disadvantage: you...
thingiverse
Wall mount for the 2018 Mac mini. ...Designed in two assemblable pieces for convenience when printing on small printers
prusaprinters
Der Entwurf wurde für 3D Drucker mit sehr kleinem Druckraum ohne auf etwas modernes Design zu verzichten entwickelt.Gedruckt mit PLA mit mindestens 50% Infill gibt dem ganzen einen sehr Stabilen halt.Getestet mit dem Apple Mac Mini 2014 und 2018,...
thingiverse
This is a replacement base piece for the 2018 Mac Mini. It will replace the existing plastic base and has a provision to mount a 120mm fan, which should greatly increase the airflow in the mini. One thing to watch is it will increase airflow in the...
thingiverse
There are a couple of VESA mounts for Mac minis on Thingiverse, but (as far as I can see) not the kind that you can use together with a monitor on the same mount. This one you can. You can also choose whether the Mac mini hangs below, on the side, or...
thingiverse
This design has a small gap to separate the Mac from the desk to avoid trapping heat and causing throttling due to heat. The Mac can be mounted upside down, but I wouldn't advise it. ... This can be also used to wall-mount it both with the cables...
thingiverse
Designed around the 2018 intel Mac mini that runs loud, I remove the black plastic bottom it just pops right off the 5v Noctua fan flows air through the mac keeping it cool and quiet. I have made 3 versions with different position and size pass...
thingiverse
I create my Mac mini 2018 case for cooling, usb hub and ssd in one body. I use for this project: 1. Satechi Mac Mini Aluminium stand as a donator for hub electronics, screws and rubber legs 2. Noctua NF A8 FLX fan 3. Step up voltage eletronics...
thingiverse
A Mac Mini model. I used it as a gift coupon. ... Instructions The bottom part (preferably black) needs to be glued on.
cgtrader
The model has a fully textured, detailed design that allows for close-up renders, and was originally modeled in 3ds Max 2012 and rendered with V-Ray. Fidelity is optimal up to a 4K render. Renders have no postprocessing. --INFO ABOUT 3D MODELS:...
3docean
The 3D model was created on real base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) -...