mac ssd adapter 3d models
124728 3d models found related to mac ssd adapter.thingiverse
An adapter plate for mounting an SSD in a Mac Pro hard drive docking bay. It uses split locking tabs to securely snap into the existing metal drive tray for fast and easy installation. ... Instructions...
thingiverse
Edited the locking tabs from this http://www.thingiverse.com/thing:108912 Those ones were too large and wouldn't snap in the holes for my 2006 mac pro brackets, so I shrunk them down and now they fit perfect! ... ...
thingiverse
I took CuriousExistence's MacPro SSD adapter design and modified it. I extended the front and back 1mm, widened the side supports and added more airflow room. The clips hold well in the MacPro hard drive sled. ...I might make the clip cylinder .1 mm...
thingiverse
This is HDD 3.5 to HDD/SSD 2.5 adapter for MAC PRO up to 2012.
prusaprinters
It will only work with SATA drives, because that's what the computer uses.The 4 small printed bolts are not strictly necessary for it to work. You do need: Mac Pro 4,1 (2009) or 5,1 (2010)big HDD mount that it came withat least 2 of the 4...
thingiverse
This is an adaptor to mount a SSD disk into a power MAC disk slot Instructions first print the ssd printsupport.stl when finished start to print the ssd adaptor without raft and without print support, watch it while printing and in the right moment...
thingiverse
this is a remixed version of the mac pro ssd adaptor made by colacristian. I found the screw mounts snapped off when i printed so I have added a sold bar for the ssd to mount to. Thanks to colacristian for the original design. ...I have not yet tested...
thingiverse
## Se trata de un soporte de discos SSD para poder usarlos en un Mac Pro. El diseño es una remix del trabajo de [**cliffcheney**](https://www.thingiverse.com/cliffcheney/designs), quien a su vez hizo un remix del diseño de...
thingiverse
This SSD adapter is used for the SSD slot of 'Blackmagicdesign SSD 4K' Video Recorder. It does not loose even when using 6.4mm SSD. It is a little tight, so please do the sandpaper after printing. 조금 빡빡할수 있으니 프린팅을 한후 사포작업을 해주세요. ...
thingiverse
This is an SSD drive adapter to mount in a standard 3.5" drive slot. Designed to work with dell clip in trays as seen in the photo above. It will fit any 3.5" hard drive tray that uses the standard side mount holes. ...
thingiverse
This is an SSD caddy for Mac pro 5.1 I remixed one from @julius111 design 3.1 version. ... Fully tested and funcional
thingiverse
G4 Cube SSD adapter for StarTech IDE2SATA adapter. This requires the removal of the airport card cage for this to fit without replacing the IDE cable. The drive rail screws onto the bottom of this adapter. I couldn't get the old hard drive heatsink...
thingiverse
The holder is intentionally oversized to allow for some airflow around the adapter. Instructions I printed in PLA with no support and 20% infill, and I used a #6 x 5/8" wood screw. ... (Strong...
thingiverse
Case for fixing broken cable on MacBook Pro power adapter. ...Instructions for fixing the cable can be found here http://www.instructables.com/id/Reparaci%C3%B3n-De-Cargador-MacBook-Pro/ (in Spanish)
thingiverse
My son needed an SSD adapter for his computer. SSD drives don't vibrate so it doesn't take too much to secure one. This adapter lets you put the SSD in a standard bay. There is access to the SSD mount holes on the side, but it is much easier to...
thingiverse
SSD Adapter V1 to stop wiggle. Just a quick design to improve the stability of the SSD upon FFG's stands. Will need to adjust with needle files, unless you want permanent on SSD use silastic to secure to stand or SSD. Enjoy modify as heck and share...
cults3d
Hard disk adapter 2.5 SSD to 3.5 HDD frame for installation in desktop PCs Dimensions 3.5 "HDD frame Length: 145 mm Width: 100 mm Height: 20 mm Dimensions 2.5 "SSD Length: 100 mm Width: 70 mm Height: 7 mm
prusaprinters
This is a small SSD mounting adapter for my Synology DS218+. ...Theoretically this should also work for other "slot"-type drive cages.Note that the latch is missing the little pin on the front.Original source for the adapter plate:...
thingiverse
The original was designed to use the small distance mount points, but I needed large distance mount points. ... I also extended the border thickness for a little more stability. Use the Offset Version to adjust the position of the SSD
thingiverse
... "Disk Tray D9" This is not perfect, but it´ll do the job. One of the fixing rails can not be inserted in the drive cage, the knob stands out to far and touch the SSD drive. Other than that it works. Feel free to remix or consider it crap. ...:-)
thingiverse
Designed a new SSD bracket from scratch. Tried to make a snap in design, minimize filament usage, and keep port/hole positioning as close to OEM as possible. The SATA ports themselves will be 3-4mm farther inward than OEM making it...
thingiverse
... one that sits inboard about 10mm and one that matches the upper part. I have also provided a SSD adapter to go in place of a fan, the M1 Mac Minis dont really need extra cooling so could be a nice stand and ssd holder for the M1 as well. ...
thingiverse
Simple adapter to fit ssd1306 into genuine u360gts case. ...A hole is a bita large, but you can adjust the size.
prusaprinters
Designed a new SSD bracket from scratch.Tried to make a snap in design, minimize filament usage, and keep port/hole positioning as close to OEM as possible.The SATA ports themselves will be 3-4mm farther inward than OEM making it incompatible with...
prusaprinters
There are pins to allow you to snap-in an SSD without needing screws, but there are also 4 screw holes underneath for mounting a standard laptop HDD as well.The SATA connector itself will be offset approx. 3mm due to the necessary railing thickness,...
thingiverse
I had no space in my NAS for more 3.5" HDDs, but spacy wall mount for 2.5" HDD/SDD. ...So, with this adapter i mounted 4xHDD discs on a 2.5" disc mounting place. ... Print with good infill like 42% and ABS or ASA against deformation.