macbook pro 2013 late 3d models
129674 3d models found related to macbook pro 2013 late.thingiverse
This is a stand to hold a macbook pro 13" late 2013 (thickness 18mm) in upright position. To protect the macbook's surface from scratches I glued 6 felt protectors into the appropriate positions. The protectors I used were about 10mm in diameter and...
prusaprinters
This is a stand to hold a macbook pro 13" late 2013 (thickness 18mm) in upright position. To protect the macbook's surface from scratches I glued 6 felt protectors into the appropriate positions. The protectors I used were about 10mm in diameter and...
thingiverse
Small print to slide over de top of the MacBook and cover the Camera. ... Sliced with Cura settings "Dynamic quality", with adjustments: - Layer height 0,16mm - Initial Layer 0,2 mm - Adapative layers Printed with an Ender 3 V2
cgtrader
I have made this model with paying close attention to the proportions and lines by patterning it to the likeness of the exact MacBook Pro 2013 13-inch I personally use. This model is natively made in Autodesk Maya, but exported in various file types...
thingiverse
### Macbook Pro 13" Late 2017 stand Designed to fit perfectly this specific model. Will not suit others. ... If you want to try it first, just print with 5% height and see if it fits your model.
thingiverse
This is a remix of the vertical MacBook Pro stand by Lorbus, adjusted to fit the late 2018 15" MacBook Pro (his was made for an older model that was thicker and didn't fit my laptop). It should fit all the 15" MacBook Pros released after 2016 (when...
prusaprinters
This is a remix of the vertical MacBook Pro stand by Lorbus, adjusted to fit the late 2018 15" MacBook Pro (his was made for an older model that was thicker and didn't fit my laptop). It should fit all the 15" MacBook Pros released after 2016 (when...
prusaprinters
These are Replacement feet for the Unibody Macbook Pro from Late 2011. For the different corners you need to cut a little bit off the model in the slicer. When looking from the bottom, the top right needs the shortest stump, the bottom left is...
thingiverse
I found a good looking and functional stand for a MacBook Pro. Unfortunately it was for a newer model then the one I own. My MBP is a 15" one from late 2008. Maybe there are others out there who own such an old gadget and would like to have a...
grabcad
I decided to completely model my MacBook Pro. I took all measurements using a 30cm ruler, often having to judge by eye. ...I did not dissasemble the laptop to get a better look at the internals therefore some parts may not be 100% accurate.
grabcad
This is a model of Apples latest Macbook Pro 15".This is done purely by looking at pictures of the laptop and modeling thereafter, so I can't guarantee that all dimensions are perfect. Still, hope you find some use for it :)The game on the laptop...
thingiverse
This is a bottom case foot for Macbook Pro 15" 2013. There are two versions of this. One is be printed with rubber like material and it has a flat bottom. The other one is for regular plastic and has rounded bottom. I ended up using the rubber-like...
thingiverse
I was pretty bummed to see that the charger on the new MacBook Pro doesn't have any cable management features. Even the little pop-out wings are gone. Here's a really simple band with a few grabbers to facilitate wrapping the cables in a ball. Print...
thingiverse
for MacBook Pro 13 2010 hold_mac_13_2010.stl for MacBook Pro 13 retina 2013 hold_mac_13_2013.stl
thingiverse
The bracket dimensions are: h: 155.6mm w: 51.4mm d: 32mm It is designed for 18mm MBPs which includes the following: Early 2013 Late 2013 Mid 2014 Early 2015 Mid 2015 2016 and newer models will fit with a mm or two extra wiggle room. There are vent...
prusaprinters
The bracket dimensions are: h: 155.6mm w: 51.4mm d: 32mm It is designed for 18mm MBPs which includes the following: Early 2013 Late 2013 Mid 2014 Early 2015 Mid 2015 2016 and newer models will fit with a mm or two extra wiggle room. There are vent...
youmagine
Fits pretty tightly, but this is by design ;-)Nozzle 0.25Speed 50 mm/sBottom layer 0.3 mmIn Fill 100%
pinshape
Fits pretty tightly, but this is by design ;-) Nozzle 0.25 Speed 50 mm/s Bottom layer 0.3 mm In Fill 100%
thingiverse
This is the 13" MAcbook from late 2009 or early 2010. I use it as a server for my home automation system in progress. I wanted to mount it under the desk out of the way. I have included files for the mid body mounts and two different types...
thingiverse
I made a macbook replica in autodesk inventor and put a lot a details into this replica. It printed really well and is a cool decoration to have. I recommend printing this upright like a real laptop, it prints best this way. ...
thingiverse
It's a stand, for a MacBook / MacBook Pro built between 2009 and 2012!
thingiverse
I added 5.5mm to cheewee200's file which was originally for a retina MBP. This now suits a non retina MBP perfectly. Enjoy. I got a little warping due to the length of the print. Laid on edge so cavities were upward so no supports were needed. ...Print...
thingiverse
The original, just 6.5mm deeper to accommodate my 2012 macbook.
thingiverse
This is a tough version of a clip to hold your Magsafe 2 power adapter into your MacBook Air. *Update: I refined it and rounded all the edges, Magsafe #1 fits a little better and is smoother. Somehow my MacBook blew a diode and won't run on...