magic the gathering deck box 3d models

Simple Magic the Gathering Deck Box with the "M" logo from Magic.

MAGIC the gathering Deck box for sleeved cards. ...Print Settings Rafts: Doesn't Matter Supports: No ...

A deck box designed to hold 100 cards sleeved with a little extra space for tokens.

the lid and box can be printed in low res the axel need to be printed in high res supports is needed on the lid and box you need to pot the axel on a raft support hope you like it :)

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=269203InstructionsUsing the following options: Move_Image_Left_Right = 38 card_type = 69 Move_Image_Up_Down = 45 image_size = 50 image_rotation = 0 input = default_TNH card_count = 40

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=269203InstructionsUsing the following options: input = default_TNH Move_Image_Up_Down = 45 image_size = 50 Move_Image_Left_Right = 33 card_type = 69 card_count = 40 image_rotation = 0

http://www.thingiverse.com/apps/customizer/run?thing_id=269203 Instructions Using the following options: Move_Image_Up_Down = 42...

This is an easy to print deck box with additional space for sideboard cards or tokens. The box fits sleeved cards. ...Based on the deck boxes by Kvermette.

customized the blank box

Both will fit sleeved cards with approximately 46mm of room inside for a deck. (Based on 63 cards in sleeves) This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/gqnx6dEX8rZ ...

This is a remix of http://www.thingiverse.com/thing:126610 done by rbschultz. ...This is only the front/back grab the rest you need from the above link.

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=269203InstructionsUsing the following options: input = default_TNH Move_Image_Up_Down = 45 image_size = 50 Move_Image_Left_Right = 33 card_type = 69 card_count = 60 image_rotation = 0

http://www.thingiverse.com/apps/customizer/run?thing_id=269738InstructionsUsing the following options: circle_resolution = 120 card_z = 100 card_y = 70 card_x = 70 printing_tolerance = 0.2 build_plate_manual_y = 180 build_plate_manual_x = 180...

Made with Tinkercad: https://tinkercad.com/things/bSMKazP2gLU

I made a foldable card box for my brother which plays Magic The Gathering. The drawing is done so if you would like to make one, go right ahead! If you are not in to Magic, there is a file without the...

Thanks to Belrius for the initial design ASSEMBLY IMAGES CAN BE SEEN HERE: http://www.thingiverse.com/thing:20431 When I printed the original box from Belrius I found that the deckbox was not quite wide enough...

Updated Files so they are all in MM This is a magnetic version of the latching box by GraffitiBatman. this uses 5mmx2mm magnets. the uploaded version does not have the name on the inside. the font...

... ...Sie sind 35mm Tief, und 70mm breit. Damit fassen ca 60 Karten mit Schutzhülle. These small deck boxes are suitable for 60er standard decks. They are 35mm deep and 70mm wide. ...It holds about 60 cards with a protective cover.

After printing the Resized version, i thought it looked quite bad with all the holes on the side, so i filled some parts in, and changed some other parts for the better imo. also made side panels with the...

A deck box based off of the Mtg Shadows over innistrad line