magnetic reptile ledge 3d models
58044 3d models found related to magnetic reptile ledge.thingiverse
Reptile Feeding ledge. ...Holds 2 1.5oz cups and is fixed to glass with 2 suction cups.
thingiverse
Magnetic Reptile Hide designed for my Crested Gecko ♥ Aprx 6x4x3in Holes for 0.12x0.47 in neodymium magnets (glue and then place more on outside of tank to secure to glass) I did three coats of polyurethane paint on the outside to ensure water...
thingiverse
Arboreal hide to hang on the inside wall of your vivarium. ...Great for geckos. There is a spot indented on the back to attach a magnet.
thingiverse
I designed these adapters to fit the Pangea magnetic feeding ledge for geckos that originally takes the large bowls to fit the smaller cups. ...I printed them in petg.
sketchfab
The ancient race of intelligent reptiles. It was completely destroyed over 65 million years ago at the end of the Cretaceous. ...More pictures - https://www.artstation.com/artwork/6aLZ2r Art was made based on the work of this author -...
thingiverse
For the full assembly you need: - 1x printed ledge - 2x suction pad (appox. ...Ø40mm) - 2x small bowls with M36x2 thread (I used this one: https://www.boesner.com/aufbewahrung-praesentation/aufbewahrung-1/leerdose-mit-schraubdeckel#62744 order...
sketchfab
Gray ledge found somewhere in Amsterdam Scanned with: +- 55 pictures Camera: Nikon D5300, 18mm Software: Agisoft
grabcad
Charmilles Robofil ledge extension for holding work. ...M6 tapped hole and slide adjustable to fit table holes.
myminifactory
... ...Surprisingly sturdy - I used these for herbs on the window sill. Requires 0.5in of exposed ledge on the bottom side. I've modeled up 0.25"-1.0" versions but have only printed/used 0.625" myself. ... Design prints on its side support free.
thingiverse
... version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: word = Ledge font_scale = 2.1 font_spacing = 0.81 pen_length = 130
thingiverse
biggest problem I found with moss ledges is getting the suction cups with the pilot holes.. but the dollar store as regular ones with a inset for metal hooks. 1 buck 6 cups.. so Solution make my own.. for aquariums you really should be using ether...
thingiverse
This ledge can clip to almost any table and be a much more convinate way to store bothersome crutches while not in use. It will hold the crutches up and out of the way. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
Use super glue or similar to install two 18mm diameter x 2mm thick, round, neodymium magnets in the recesses in the back of the ledge. Use two more magnets on the outside of the tank wall to install the ledge. If the ledge slips down the tank wall,...
thingiverse
This feeding ledge encorporates standard 10mm neodymium magnets to hang on the side of a glass terrarium. The recessed feeding dish trough is designed to use recycled water bottle lids. ... *Updated version uses mm for slicing convenience*
thingiverse
Use 20x5 magnets to hold on glass (i tested with magnets on ledge side and 20x20x3mm steel washers on outside and hold is ok in 4mm glass) Back side there is 3 holes for silicone buttons to give more grip to the terrarium wall (8x3mm) Can also use...
thingiverse
Design for a magnetic gecko feeding ledge. Made to fit Solo P150, P200, or P250 portion cups or any other similar cup with a 2.4 inch (~60mm) top diameter portion container. It is loose enough that 2.5" portion cups should also work. The space for...
thingiverse
Fingerboard ledge Inspired by Blackrivers Mike Schneider III
thingiverse
designed this euro style bench/ledge for tech deck fingerboards. ...
thingiverse
Flexible reptile to decorate your walls or refrigerator doors. Salamanquesa flexible para decorar sus paredes o puertas neveras. It may or may not carry magnets. Salamanquesa flexible para decorar sus paredes o puertas neveras. Puede o no...