stratux case 3d models
203596 3d models found related to stratux case.thingiverse
This is another 3D Printed STRATUX case, with a SubD-9 for serial connection to an EFIS an be able to power the Stratux without the micro-usb. There is on the lower part 3 slots for a PCB to be inserted for Attitude/Heading/Baro of widths 10mm / 17mm...
thingiverse
This is a Stratux Case designed to directly mount the RY836 to the top. It is designed for a Raspberry Pi 2. The Power and Activity LEDs are in a different place for the RPi3. **Update:** I have added versions for the RPi3 but they are untested. ...
thingiverse
This is a case for the Raspberry Pi Stratux. I had a few requirements I wanted to meet when I designed this: I wanted an internal antenna I wanted a case that would clip shut, not requiring any screws or fasteners. Support for the AHRS module Lots...
thingiverse
https://www.myminifactory.com/object/3d-print-176151 ===== I made my own case to assemble the [Stratux kit](http://stratux.me/). The idea is to keep the antennas in place, but occupying the smallest area. I'm using 1 fan (30x30x7mm), it came...
prusaprinters
I made my own case to assemble the Stratux kit.The idea is to keep the antennas in place, but occupying the smallest area.I'm using 1 fan (30x30x7mm), it came with several screws and nuts and I'm using 10 screws and 8 nuts.4 screws and 4 nuts to hold...
thingiverse
Designed to hold the Stratux Squared of slim case. Edit: New versions that fit the Laser cut acrylic case are available. Just look for the files with ACR at the end. http://www.thingiverse.com/thing:1714431 All three are designed to take three...
myminifactory
I made my own case to assemble the Stratux kit.The idea is to keep the antennas in place, but occupying the smallest area. I'm using 1 fan (30x30x7mm), it came with several screws and nuts and I'm using 10 screws and 8 nuts.4 screws and 4 nuts to...
thingiverse
Clip for the Stratux ADS-B case sold by Stratux on Amazon, listed as Stratux Case with Fan, White ABS. The screws provided with the case are probably long enough. I got new screws at Ace hardware for the top but have since countersunk the holes in...
thingiverse
This is a case for the Stratux ADS-B receiver. It has room for 10,000mah battery and raspberry pi with uninterrupted power supply. I've go 6-8hrs of runtime depending on the ambient temperature. The GPIO pins need to be cut down so the UPS HAT sits...
thingiverse
edit: Unless you are using really old mini sized SDR's do not use this design Yet another case for the Stratuxhttps://github.com/cyoung/stratuxhttps://www.reddit.com/r/stratux/ This layout increases the length of the case by 21mm but decreases the...
thingiverse
This "Dual Stratux Case" is an advanced version of https://www.thingiverse.com/thing:5320658 and now supports two T-Motions/ softRF to send multiple protocols at same time, such as: 1st T-Motion/ softRF transmits OGNTP (Open Glider Network Tracking...
thingiverse
The case is available with different options: 1x 30x30mm fan to cool down the NooElec Nano 2(+)/ 3 SDRs and 0.96inch display support (you can cut out the display hole by using a knife) 2x 30x30mm fan to cool down both, the NooElec Nano 2(+)/ 3...
thingiverse
The case is available with different options: 1x 30x30mm fan to cool down the NooElec Nano 2(+)/ 3 SDRs and 0.96inch display support (you can cut out the display hole by using a knife) 2x 30x30mm fan to cool down both, the NooElec Nano 2(+)/ 3...
thingiverse
... + RY836AI. Connectors are SMA, fan 30x6mm. Hardware the same as for my Stratux Slim Modular Case. https://www.thingiverse.com/thing:1920485 . USB socket has all the connections soldered. Side antenna mount has relief for side venting. ...
thingiverse
You can read more about the decision to leave the RY835AI out here: https://www.reddit.com/r/stratux/comments/3wjdeb/new_micro_case_with_external_gps/ Let me know if you want any changes. ...I could add holes for the MCX male cables if you want to use...
thingiverse
This is a case for permanent install of a Stratux in a plane. We installed ours in the tail and used remote antennas on suction cups in the windows for the GNSS, 978, and 1080 mhz antennas. The power connector is a 4-pin CB mic connector with a...
prusaprinters
Compact case for Stratux ADSB Receiver. Print instructionsDecided to make a compact case for Stratux receiver. BOM : 1)Smraza Cooling Fan for Raspberry Pi 3 with 3 Pcs Heatsinks DC 5V for Raspberry Pi 2 Pi 3 Model B, Raspberry Pi 3 B+ 2)uxcell® Power...
thingiverse
This case is designed to work with the zero4u USB hub. There are two versions one that has two holes for SMA extensions and a version with only one hole. I use the single hole version and an SMA to dual MCX splitter for use with a belly mounted...
thingiverse
Edit: This case has been superseded by the squared off slim case as it prints much more successfully Thinnest case I have managed yet. 24mm and holds dual Nano SDR's and a VK-172 GPS. Has the option of passive venting or a 30x30x7mm fan. Not enough...
thingiverse
Designed for a set of MCX-SMA straight through adapters with a hex portion for the case to grip. Like this http://hakshop.myshopify.com/products/sma-female-to-mcx-male-adapter However the opening will allow you to plug in the stock antennas. Case...
thingiverse
FD Remix Stratux Case with softRF/ T-Motion (1 Fan + OLED support) Case adjustments: - on/off switch hole removed - Hexagon holes + 0.3 mm for better mounting - ventilation slots additional plastic -> a bit more sturdy Lid adjustments: - additional...
thingiverse
## Background I had printed mistertech's Stratux case earlier and assembled my Stratux with a GPYes (https://amzn.to/2Wf6Aob). I experienced GPS accuracy and reception issues with the internal GPYes unit like many other Stratux users have also...
prusaprinters
When I find some time, I'm going to design a brand new case specifically for mounting in the rear C172 window for better sky visibility and using the external GPS unit. Background I had printed mistertech's Stratux case earlier and assembled my...
thingiverse
Stratux case with modular components to accommodate Raspberry Pi4 and Pi3 boards One could just print the Main Body and the Case Cover (Choose One-Piece or Three-Piece) and call it good. The other components are optional enhancements. I printed the...
thingiverse
The case is then glued to the bottom of the Stratux case and rubber feet added to provide a non-slip mount. The battery can be held in by a rubber band or velcro straps. Works like it was made for it. ... ...
thingiverse
Case for Stratux Softrf T-Motion Parts: - Stratux - Softrf T-Motion Dongle - Softrf Skyview ez - usb to serial converter - usb A board - usb micro board - capacitor 1000uf 6,3v - div. ...cables
thingiverse
This is a somehow modified Slim Case by helno - SD card opening is cut deeper for easy removal, more vent holes. The modules can be design to fit a different components mounted to Raspberry Pi - GPS, AHRS etc. ...Hardware is 2-56 screws and brass...
thingiverse
This is my Stratux case. My goals in designing this case were: Compact, short No support needed Folding antennas that do NOT rotate around the mounting axis. Label the top cover to make it easier to remember which antenna goes where (978Mhz and...
thingiverse
Inefficient (too wide, will have revised model out next month) dual SDR Stratux case for small printers. Washers file is for if you break the pi mounting studs. you can use M 2.5 screws to secure the pi using the washers. Print Settings Printer...