maker select v2 replacement parts 3d models
760640 3d models found related to maker select v2 replacement parts.thingiverse
At some point, I lost one of the spacers for the extruder heatsink on my Monoprice Maker Select V2. I made this one to replace it. If you lose one of yours, print this as a replacement. ...:)
thingiverse
This Holder fits in the 2 rectangular shaped slots that are in 3 spots on the Maker Select V2 Frame.
thingiverse
Hold a glue stick, all the tools that came with your maker select V2, and a set of calibers!
thingiverse
LED strip light holder for Maker Select v2. The 8mm offset was used for the upper mounts to clear my frictionless spool holder and filament guide. ...I use 4mm offset for the sides.
thingiverse
Used with LumberjackEngineering flexible mount system to mount a PanelDue on Wanhao i3, Maker Select v2 or Cocoon Create and made to use the 4 pin (1x4 Dupont) connector
thingiverse
Parts 3mm screws of appropriate length & 5015 Good Blower (12V for MonoPrice Maker Select V2) Use ABS although PETG ought to be fine. I designed a raft and support into the model and found it came right off without difficulty when using ABS. Use...
thingiverse
As most owners of the Maker Select V2 have probably noticed, the provided spool holder is too thin for most filament spools. This design extends the provided holder by about 2cm, making it plenty big for most rolls. It has a semi-rounded top for low...
thingiverse
This wire shroud was designed to protect the wires over the extruder when the maker select reaches its maximum Z axis height (178mm). ... This design was based on the Wanhao Duplicator i3 V2 Wire / Cable Shroud by Airmaxx23...
cults3d
... late at night. ... I made this holder to have a place to store it so it doesn't wander off. It hangs from one of the pairs of vertical slots on the side of my monoprice maker select v2. ... I don't know if other wanhao clones have these same slots.
thingiverse
... late at night. ... I made this holder to have a place to store it so it doesn't wander off. It hangs from one of the pairs of vertical slots on the side of my monoprice maker select v2. ... I don't know if other wanhao clones have these same slots.
thingiverse
This base plate directly bolts on the monoprice maker select v2 and compatible printers. Printed great with PETG. NO PTFE TUBING NEEDED Print, bolt on, Print Flex. That easy I have found that I have NO ISSUES with retraction and have made...
thingiverse
... 'nub' that snaps into the corner which holds it better than original. Print Settings Printer: Monoprice Maker Select v2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 20 Notes: used PLA at 200°C print head and 60°C bed temperatures.
thingiverse
This is an enclosure for the maker select v2 made out of a cheap bed side table and desk. I still have to mount the control box underneath the desk but have to design some support brackets. Up top i drilled a 1 wide hole for the filament to go into...
thingiverse
I got a Monoprice i3 Mini from a friend which has a lot of missing parts. some of them could be 3D printed hence created these. - Leveling screw. The Level screw has an insert for M3 nut, hence pause print at a height where the layer over the nut...
thingiverse
Allows the Maker Select v2 LCD board to be mounted on the bottom right side of the Maker Select frame, or to sit (freestanding) on a desktop. **Assembly** The face plate mounts to the LCD board and the base optionally bolts to the MS frame...
thingiverse
... supports that is needed is for the rail in which I used custom supports from cura. because I installed the Z Extensions for Wanhao Duplicator i3, Cocoon Create, and Maker Select i needed something that would attach to my printer so I created this.
thingiverse
... is still a work in progress, any feedback is appreciated! ...I made this as a remix of https://www.thingiverse.com/thing:1718783 It clips onto the side of my Maker Select and holds my Allen Hex Keys, Scraper, Wire snips, Drill bit, and MicroSD Card.
thingiverse
Accesorios para impresora Maker Parts V2 3030. Consiste en un clip para sostener el flex cerca de los cables que van al estrusor. Una cubierta para la pantalla. Un soporte para poner un tubo flex para guiar el filamento hasta el estrusor. Un...
thingiverse
Filament guide I designed for a spool mounted off of the printer. ...Maker Select V2.1
thingiverse
The kid really needs your support, and his goal is to reach 500 subscribers: http://goo.gl/ELT7ii Intentionally designed to look similar to the original MP Select V2 spool holder arm, hold larger (up to 74mm wide) spools, and prints WITHOUT supports....
thingiverse
A small stand that connects to the Maker Select V2 control box that will hold the included spatula and a pair of diagonal cutters.
thingiverse
This adapter was created in order to move the gantry forward on my Monoprice Maker Select V2 after I upgraded to the 4mm Y carriage from RepRap Champion on Amazon.
thingiverse
I was looking at the filament release lever on my Maker Select v2.1 a few days ago and noticed that one of the sides of the filament insert hole was misshapen - it looked as if constrant rubbing of filament against it had scraped part of it off. I...
thingiverse
I bought a used Monoprice Maker Select V2 3D printer and noticed it was missing the filament cooling fan and shroud/mount. I looked on here and couldn't find one, so I made one (the light blue part in the attached picture). Figured if anybody else...
thingiverse
... printing out all four. The design takes into account clearance for the Y carriage to travel and should just make it easier on your fingers to level the bed. Print Settings Printer: Maker Select v2 Rafts: No Supports: No Resolution: 0.1 Infill: 15%
thingiverse
I really liked grommel's spool holder, but I have a Maker Select v2 with different mounting hole placement than the i3 plus and I didn't have the larger bearings used in that design. Modifications to the original design include: - Relocated mounting...
thingiverse
Monoprice Maker Select v2 Mosfet Mount. This bracket is for mounting side by side with the melzi board. The holes on the board are large enough to go over the melzi board mount screw base. ... Please attach the bracket to the mosfet first then mount...
thingiverse
This camera mount is designed to attach the the Monoprice Maker Select V2's base plate and slide back and forth without interfering with the print bed. The rotating base and arms used where sourced from here. ... ...
thingiverse
So i wanted to get rid of the bulky box on my maker select V2, but none of PSU bxes on thingiverse fits the MEAN WELL LRS-200, so I decided to make my own that is light on filament functional for needs.