makerbot replicator 2 active cooling fan 3d models

A video (youtube.com/watch?v=y96ulMCkNMM) showcases the thermal distribution of the Replicator without the head cover, revealing that the cooling fan also cools the model excessively, causing it to distort. Photos of distorted models are available at...

The model was sliced at 2 shells, 15% infill, and 0.3mm layer height in Makerware, built on Replicator 2. Remove popout tabs for installation. I had to adjust a zip-tie due to interference, but it's centered now. ...Wishing you success with your build!

Revise the 2X printer's spool holder by replacing the original one with a universal fit design that accommodates various spool types, including Makerbot and Octave. V3 features a 10mm shorter Octave spool holder and reinforced walls for the Universal...

Designed to accommodate the standard Makerbot spool, it is also suitable for Australian filament deliveries. It offers excellent low-friction spooling performance. This model utilizes standard roller-blade ball bearings (22mm OD, 8mm ID, and 7mm...

This is a detailed guide on how to convert a Makerbot 3D printer to use Ramps 1.4 board, external thermocouple, and reprap LCD controller. The conversion involves replacing the original electronics with new components, wiring them together, and...

Here is an overview of the project: **Pre-Build** * Rip out original electronics, leaving wiring and connections intact * Purchase all necessary parts from the parts list * Glue power supply, Ramps 1.4 board, and external thermocouple board to the...

Engine cooling radiator fan wheel

I redesigned my last WebCam mount for my Logitech C910 WebCam. ...This one does not require any fiddling with the WebCam to make sure it does not get hit by the extruder head on very large prints, or during the initial filament melt along the front side...

I'm not sure if this will work for anyone else, but it worked for me like a charm! I had my doubts, though - what if it breaks your build plate in half or causes some other disaster? My warpage was so bad that it wrapped about a foot of filament...

I will add more soon. ... Category: 3D Printer Accessories

A 130-watt heater is being referred to, which likely provides efficient heating for the specified area.

This custom spool holder is engineered to accommodate smaller diameter, thicker spools with precision. Please note that rigorous testing has not been conducted, so verify the dimensions carefully before use and make adjustments as necessary. ...A...

I just redid the foot insert for thing http://www.thingiverse.com/thing:232984 I made a slot for the nut that can be heated and pressed in. I also made the joint solid. ...Props to oliasmage for thing.

Customized Version of a Popular Online Resource: Created by Using the Unique Features of a Leading Online Application.

This is a printable substitute for the REP2 secondary y-axis. ...Ideally, it should be printed with a high-temperature material like PETG, nylon, or ABS.\r\n\r\nNo supports are needed.

I am preparing an expansion and will add much more shortly.

Allows removal of the X-axis drive belt without loosening motor X using 3mm screws.\nRequired when pulley lubrication has resulted in support destruction.

I revamped my existing webcam mount for my Logitech C910 camera. ...This model necessitates no adjusting of the webcam to ensure that it won't be struck by the extruder head on enormous prints or when the filament first starts melting at the front edge...

I really liked Thruit's original active cooling duct, but I didn't always want it on my printer. Screwing it on was a good way to fix it, but it seemed too permanent for me. So, what I did here was add a handle big enough to get a finger or thumb...

... I bought a 3D printer for. I got brainstorming in Tinkercad and eventually came up with the idea of a clip-on shroud to hold a couple of spare cooling fans I had lying around from another part of the project. ... The rest is basically history.

... I bought a 3D printer for. I got brainstorming in Tinkercad and eventually came up with the idea of a clip-on shroud to hold a couple of spare cooling fans I had lying around from another part of the project. ... The rest is basically history.

... of no less than 40mm. It fits two high-speed 30mm fans. You'll typically find high-speed, high-flow 30mm fans by looking for "RC Cooling Fan". And, for the record, the project's name is pronounced "Mugen" or "Microgen". Category: R/C Vehicles

Flsun Cube Cooling Fan Prototype Version 1.2 We Should Rotate It -90 Degrees So That It Sits Perfectly

Ender 2 4020 Cooling Fan Adapter I designed this for my own setup. ...I could not find a 4010 blower fan, so decided to create my own adapter.

Fan shroud for 12vdc blower fan fits directly on to Ender 3 original hot end cover with M2x20mm cap head screws and M2 washers, cable had to be extended (soldered length of 2core servo cable insulated with heat shrink and fed into braided sleeve),...

Although it's mounted in my garage, I'm in Arizona so it definitely gets hot - my first one died after a bit under a year, and measuring the heatsink on the back it can easily get over 140f - so I decided to put some 120mm ducted fans on the top (to...

Rev.1 (Horizontal) Fan Cooling for the Controller Board Ultimaker 2/2 +. Four screws for the fan with cap M3, 25mm long and To attach M3, 30mm long screws. Suitable for 40mm fans. The 24V fan connects to the J20 Jack (19-24V) port on the UM2's...

I'm upgrading my Ormerod 2 by installing two new fans to enhance cooling for the print area. I've chosen the Noctua NF-A4x10 FLX, which are renowned for their incredibly quiet operation. ...To securely attach the extra fan, I utilized a fan spacer, and...

This model was created using Tinkercad. ...Make adjustments right now at https://www.tinkercad.com/things/8QGzjy5u3xT.

cooling fan for 2.5 inch HDDs ================== used to hold several 2.5 inch HDDs plugged into the back of my smart tv via a 7 port powered usb hub which also powers the fan This was designed specifically to fit the 80mm "Thermaltake Mobile Fan II...