masonry line block 3d models

I had to reduce gyro lpf on yaw to 60hz to get a clean gyro line. This may have to do with vibrations coming from the frame itself. The motor has most vibration around 150Hz, so I set notch 1 to 120-160hz. Dynamic filtering might do a great job, but...

Then, I put a small layer of rocks at the bottom to really help oxygenate the soil (this step is optional, and probably unnecessary.) Then, I filled the container to the fill line with potting soil (I used potting soil because I had it on me, but...

A brim of at least 15 lines is necessary to prevent the pens from wobbling once they reach the top inch. This presents a problem, as the brim will cover the nib entry point. This can be fixed by breaking through the brim layer, I used a thumbtack,...

Ensure that LEDs line up with the pattern of shade. This part is bit tricky</li><li>Fit the power jack in to the hole of the base and fasten it with the screw nut</li><li>Mount the esp board into the snap fit bracket of base.</li><li>Connect the...

If you want to use this regularly, I would recommend buying a commercial bidet, mostly as it is easier to clean. Changelog: v2: thinner walls, as big walls were not necessary with petg, faster printing time, bigger screw on cap (more stable), 25%...

I did increase the Wall Thickness to 1.2mm so that Cura would increase the Wall Line Count to 3. Other important settings are 200C print temp, 60C buld plate temp, 10% infill using triangles, 50mm/s speed, Z hop when retracted, print cooling at 100%,...

The Neopixel range of addressable strips and rings seemed perfect, needing just a single data line for RGB control and a 5-volt supply. At the same time, I wanted to improve the mediocre fan duct on the Kossel. There were plenty of designs online...

 Place the RPi 5 into the top, ensuring everything lines up adequately with the cutouts and screw holes.  Place the bottom onto the case.  Check that everything aligns flush around the case and that no wires are sticking out. Secure with 4 M3...

One shortcoming of the Taz line of 3D printers is the lack of an enclosure that regulates temperature effectively, ensuring longer/larger prints with ABS or HIPS do not have layers separate during the print process. To address this issue, I...

Running the shower as needed to purge stagnant water can cause a massive mess and slip hazard, as well as damage water-sensitive construction materials like drywall and wood.&nbsp;To prevent damage to my lab, I built this printed adapter so that...

Includes one TY-55 "Rex" Transport Aircraft as a Poser figure model (obj, cr2, png)-Highly detailed, with many panel lines and rivets included in the modelled mesh.Includes the following accessories, parented to the hull under the left wing and right...

If you produce new work with this model and wish to share it with us, please drop a line at web@smk.dk or stw@myminifactory.com. This scan was produced in collaboration between The Statens Museum for Kunst and Scan the World for the SMK-Open project....

I removed the filament mount from the top of the printer and remounted it to the top of the table, then drilled a 1/4" hole in line with where the filament would normally be coming down. I plan to replace the stock filament mount with this...

I also printed both with the z seam lined up at the same point, and it makes a great guide for when it's fully tightened together (see the pictures). Mine are printed with the superhard carbon fiber polycarbonate off Amazon, but PETG should also...

So I created this 30x30x30 mm cube which contains several functions.The print takes about 1.5 hours.Below are pictures from which you can take some measurements to check your cubes for dimensional accuracy.You can check the following properties on...

All power supply lines are completely out of danger of being hit by leaked water. 1/ Water leakage when the printer is not turned on. The tank and heat exchanger are located lower than the water cooling of the hotend. Therefore, if water leaks...

Delicate hand-carving along edges and curved lines adds softness, giving this furniture a romantic appearance. Dimensions: 50cm in height, 117cm in width, 53cm in depth. The total weight is approximately 26 kg. Part number: 501.40175 Price: €...

so you can also use a real gopro base with stickypad on the back of any display case you already have. (NEED TO KNOW) i designed this box for my ramps-fd that i slightly modified. originally all the connectors are facing away from the board .and this...

  Print Orientation is the same as the final mounting orientation (big, flat side down), although this does put the layer lines in an orientation that could cause the part to shear if you are really rough with it.  No supports requiredI printed my...

This will add the line affect from the first layer print and remove the need for supports. After printing, the 8 - 5mm neopixels are wired as a strip and added to each conduit using the cut outs on the back so the wires are flush. A bit of hot glue...

To achieve this, use the 'Extrude' tool by clicking on the button located at the top right-hand side of the screen which will enable you to create a 3D shape based on a selected object or line. To start extruding your cube into a mountain range,...

Cut on the line. Add a thin layer of glue (from a glue stick) around the outside edge of the material.Step 3.  Slice the Ornament. The ornament should be sliced with a pause print (M601) inserted at the 4.6mm layer.  [Go to 1:04 in the Prusa video...

I've included some sample code below - just open your gcode file and insert it on the line before that layer begins. Print! When the printer pauses, insert one hex nut into each of the three holes. If you printed the embedded bearing version,...

-Two lengths of wire to run from the switch to your driver board -A quick tweak to your firmware to enable run-out detection Construction: -Screw a Bowden tube connector in to the output side of the extruder body -Screw the extruder body to your...

A good way to check this first is putting all 4 pieces together first, the little U shaped cutout at the top of the wallet should match up with all 4 parts.Take the elastic band from earlier and fit it around one of the inside parts.Take one of...

The supporting system can be reused multiple times.\r\n\r\nMaking cute Pom Poms is not rocket science, but with this system it's easy to create them quickly using a few simple steps.\r\n\r\nJust print two parts of each size, and align them so the...

When customizing the BASE part, use the exact same values for the parameters as here, or it won't line up and fit.\r\n\r\nTo help you out:-\r\n\r\n### MKS SBASE\r\n> Board Length 146.5\r\n> Hole Offset 4\r\n> Board Width 95\r\n> Top Gap 6\r\n> HBP...

Do not contaminate the shields and then hand them out to front line workers! If you guys have any suggestions for further improvement please let me know! Original design and good info from Prusa can be found at prusa3d.com/covid19, another model I...

The back section has vents on the bottom - set up your slicer to print them as bridges (horizontal and vertical lines, not diagonal) and they will look like awesome vents when done (In Cura, you can do this by going into the Experimental settings and...

Remember to stay patient and take your time, as rushing through the repair process can lead to further complications down the line. If you're still having trouble after attempting the repairs outlined above, consider consulting the user manual or...