massive droner 3d models
6420 3d models found related to massive droner.thingiverse
Remixed to mount SQ12 camera on the Catalyst MachineWorks Massive Droner. Expanded the SQ12 casing a few tenths of a millimeter for a slightly less tight fit. I think it fits perfect now with a little assistance from a heat gun before installing the...
thingiverse
Parts for the Massive Droner and More Massive Droner frames. Print two arm guards per arm and glue them together around the arm (MMD only). The xt30 holder may be glued to the back brace on the More MD. The canopy has two antenna tube...
thingiverse
TPU Mounts to utilize the Sharkbyte TX5M.1 on the Catalyst Machineworks Massive Droner HD with the minimortal antenna. I used a Foxeer Lollipop antenna but since the antenna support is designed to have the cable tied to it any MMCX should work. ...
thingiverse
this mounts the camera too low and you can see the frame in the video use the mount in the massive droner parts file This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fGHlUzbriDO
thingiverse
A GoPro mount for the massive droner. ...At around 20 degrees.
thingiverse
... my RX antenna, and wanted to mount my VTX antenna (Foxeer Lollipop 3) cleanly. I'm using it on the 3" More Massive Droner, but it should also fit the 2.5" Massive Droner. ... STL includes support, which should be easily removeable post printing.
thingiverse
... Temp: 215C Plate: 60C Note: Bumpers should push through and self-lock in place. Their meant to be hard to insert so they don't slip back out. Frame can be found here: https://www.catalystmachineworks.com/products/more-massive-droner-3-inch
thingiverse
First I wanted turtle mode. Second I wanted protection for the Axii stubby and antenna wires. ... Razorback is also a nice touch.
thingiverse
Here are arm guards/soft mounts, a front standoff and rear standoff with antenna tube mounts. The antenna tubes will be mounted at a higher angle for more prop clearance and fit much tighter than they do in the stock mount. Print in TPU. ...I added a...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/dHcn3SJs5ok
thingiverse
I didn't like the stock mount with the Massive Droner HD and the angle it put the antenna at so I created this.
thingiverse
Replaces the tpu part for the catalyst machineworks massive droner 3 inch hd. Mounts an immersionrc ghost qtee antenna and a vista antenna. ... full build: https://rotorbuilds.com/build/26782
thingiverse
The frame is Catalyst Machineworks Massive Droner This design has a holder for micro camera: https://www.banggood.com/Super-Mini-Light-AIO-5_8G-48CH-200mW-VTX-520TVL-14-Cmos-FPV-Camera-PALNTSC-for-QX90-QX95-p-1095683.html?p=V326016082379201608W...
thingiverse
Lightweight and minimalistic arm pads for the CMW Massive Droner 2.5" Micro frame. Designed to only protect the front edge of the arms, keep it light and simple. I'm also a madman and crammed a Runcam Hybrid into the frame, and the HD cam sticks...
cults3d
This is my first design, so it's not perfect. Please don't complaint but I don't mind constructive critique :-) It's design for TPU and the fit is really thight for the AXII and the antenna tube (3mm). The goal is to simply protect the AXII and give...
thingiverse
This is my first design, so it's not perfect. Please don't complaint but I don't mind constructive critique :-) It's design for TPU and the fit is really thight for the AXII and the antenna tube (3mm). The goal is to simply protect the AXII and...
thingiverse
Print In TPU, The front bumper can be difficult without supports
thingiverse
Worked up these mounts to pack a TBS Crossfire Nano and Immortal T into the very limited space on a CMW Massive Drone HD. Printing: Everything will need printed in TPU. Qty for each piece is 2 .20mm Layer Height 20% infill Priline TPU...
thingiverse
GoPro hero 6/7 mount for Raging Droner from 20 to 45 degree. No props in view. The earlier version has been upgraded to prevent jello. Use D40 TPU or something stiffer Print profilv5 with infil 20% or less. It does not matter Connector have to...
thingiverse
Fin for the Catalyst Machineworks Raging Droner 6.0mm Fin to aid in turtle mode. Spacer used to center the front part of the fin. Use with my Antenna Block for a better rear fit. ... 20% infill with 3 wall layers
thingiverse
Customized version of http://www.thingiverse.com/thing:165411 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=165411 Instructions Using the following options:...