masterbox q300l mod 3d models

To assemble this mod, once you have my direct drive adapter printed (I suggest to print it turned 90° ccw, also put the Z position to 0 in your slicer; supports enabled, 100% infill, 4 perimeter walls, 6 upper/lower layers), you have to remove the...

Here is my upgrade/mod of the Sidewinder X1. Thanks to the linear guide, there's a super-stable X axis. For me, it has led to better results. The best thing is that it's 100% disassemblable since no holes are drilled or parts are changed/damaged. B.

Also, you can find all connections for all the parts to the Gotek board in https://github.com/keirf/FlashFloppy/wiki/Hardware-Mods Of course, all this needs some soldering/unsoldering skills, and to be very patient and careful, so I'm not...

I had been trying out different hotend mods and parts cooling ducts for about a week now and I wasn't having much luck as I realized two things... 1) Creality really made the cooling fan on the stock setup as efficient as they could have given the...

Print Settings Printer: Heavily modded Craftbot Rafts: No Supports: No Resolution: 0.2 mm or less Infill: 20% or less Notes: Any 3D-printer should work, this is an easy print. Print one of each model. If you orient the models properly (largest holes...

you will be reposining it for this light mod. install 24v to 12v converter box (I used a hot glue gun) attach 4 wires to 24v to 12v converter box drill hole to reposition heated bed power control box attach heated bed power control box wire circuit...

Tips from my build: use a cheap 5 gram servo, not a 9 gram servo (which I found to be unnecessarily big requiring a deeper base cover mod). Popsicle sticks hot glued into the body on either side of a small 5g servo work very well as a servo mount,...

This is a mod of the tarot 250 frame. my setup: Naze32OrangeRx DSMX 3Ch S.BUS 2.4Ghz Rx (twin long antenna version) Gemfan 5040 Multirotor PropellersMultistar Elite 2204-2300KV Afro ESC 12Amp OPTO Ultra Lite Multi-rotor Motor Speed Controller...

... matter of drilling new holes in the correct positions. This system could potentially be used for hardcore computer mods and various other applications. ... Viewers are invited to check out my other uploads by liking and subscribing to my channel.

I've modded the original with right-hand filament cooler so that the magnets I have lying around from my R/C hobby will fit perfectly. The magnets are six-millimeter round shims and two point nine millimeters thick. Here's a link to the magnets I...

Brawl's Project M mod. The default garb, inspired by his look from Ocarina of Time, has been a staple of the character's design since its inception. However, some players crave something fresh and different. A popular alternative costume for Link is...

More information on the Eachine E010 and similar mods can be found in this thread at RCGroups. Print Settings: Printer: Wanhao Duplicator i3 Rafts: No Supports: Yes Resolution: 0.1 Notes: My printer (Prusa i3) required supports everywhere. I used...

I did most of my test printing on a Monoprice Select Mini V2 that has a buildplate mod as well as an E3D Hemera. In every coin trap that I have published I have tried to add a bunch of textile features to add to the experience of playing with a coin...

Setup allows for using larger cooling mods such as 7530 or dual 5015 without concerns of losing additional Y movement Removing V1.0 from the post. Update 2021-09-19: V1.0 I noticed the Z screws would start whipping, sometimes quite violently...

And because the ship is too small for a standard docking collar, it would not generally be used to RV with or travel on JumpShips - although it would be possible with a heavily modified bespoke attachment (but that would be like putting expensive...

However, once it's up and running, I plan to go with the internal mod. My initial solution involved zip ties and tape, but it looked janky. Then, I used a mount from The Maker Boys, which was too heavy and far away from the goggles. I took...

This mod eliminates around 80-90% of the wheel plate flex on a Playseat Challenge. The glove box is really cool, but optional, if you don't want it just print the right arm twice. See before/after video here https://youtu.be/5B6NBgwF4yE ...

The two 5mm tall nubbies on the bottom piece keep distance for the other side.Feel free to modify the Fusion360 file and re-post if you make mods. I will say I don't like that I can't see the status LED lights. I was going to add a cutout area for a...

You will have to remove the top plate and Vista to do this mod, but it's not difficult at all and only takes a few minutes. You may have to desolder the XT30 or desolder the power lead from the FC to thread it through the mount, as with the...

I'm publishing this thing before I've finalized several details, because a couple of the files I've made might be a nice starting point for someone else to make a top case mod, and there's enough time left that they might get to make use of them. Rep...

... cap, but if you put a little silicone lubricant on the threads, the cap will go on easier. If you happen to mod the model to use a coarser thread for the top cap and you've tested that it stays closed ok, it'd be cool to add a remix that way. ...

(this is the key mod that breaks compatibility with @russross system) the supporting bars were moved slightly towards the rear, for the sole aesthetic purpose of moving the face of modules in-line with other components on my network rack finally, a...

If you don't want to install this extra extrusion rail I have another version of the rear motor cage that is better than standard, but is not stiff enough to be part of the Gold Series of mods. 7. The motor can be moved back and forth in it's...

(this is the key mod that breaks compatibility with @russross system) - the supporting bars were moved slightly towards the rear, for the sole aesthetic purpose of moving the face of modules in-line with other components on my network rack - finally,...

This is my own take for the Eryone hotend fix after constantly removing the whole thing to fix the clog So this modification is inspired by other mod by ve5yan https://www.thingiverse.com/thing:4881419/files This modification will work on BOTH MK8...

The least of these issues is a loss of about 7 mm on the Ender 3's total 230mm length with the stock Cr mod, whereas others take up around 15 mm or more. Here's a summary of my modifications: 1. I redesigned the interface between the fan duct and...

Holga 6X12 Super Wide ================== Inspired by some of the Holga mods I have seen I decided to modify my Holga 120 WPC Pinhole Camera into a 6X12 Super Wide. I used the Pinhole Holga as at the time it was easier and cheaper to get my hands on.

A collection of 11 Kotor Blaster that I, you guessed it, ripped from a TTS mod and edited. since the models are reused in game you can just paint them yourself to be any one you want. All models are individual I just included screenshots of them all...

Overview I was interested in a plotter mod that didn't need to be bolted or permantanly mounted to work. My design allows for a quick addition by just slipping on the extruder fan cover without any screws or bolts. As well the pen grip is tightened...

Like I said none of these really do fit as when you have to scale them when slicing it comes out of proportion and its not working. I had a specific Power rocker switch with fuse that I wanted to use. So I designed this very crudely but very...