mic flag for shure sm7b 3d models

... bracket in the factory location. The hole for the mic ended up being slightly small but a little heat from a lighter allowed it slide in. I printed with pla, no top or bottom layers and 30% honeycomb infill. ... This was for a 2010 Toyota Seqoiua

Added linear knurling for better grip and redesigned the nut to allow full tightening of the mic in the mount (even the original Samson collar nuts had this issue). Three versions are available: one with a flat bottom that is easy to print, another...

I needed a way to change from a handheld mic to a headset mic. I've designed this with the ability to change mics quickly at home or in the field. The Yaesu mic uses a standard CAT6 style connector. I wired two 3.5mm jacks to a CAT6 Keystone...

I've had great success using a Zoom H1 (available on Amazon) when the field of view is set to Narrow, or a Rode VideoMicro Compact Mic with the GoPro still set to Wide. ...My idea was inspired by this innovative product: Polsen GPMK-22 GoPro Stereo...

I had to whip up a makeshift boom mic on set without breaking the bank, so I cobbled together a simple connector using a hot shoe for a microphone and a trusty broomstick. By threading an M5 nut and bolt through the joint, I was able to secure the...

... managed to get one that fits like a glove. It features the standard 5/8" 27 threads you'll typically see on your mic stand, and they synced up perfectly for me. ...Just remember to take it easy when attaching the mount to avoid any threading issues.

Case for the ReSpeaker 6 Mic Array - A Comprehensive Solution Upgrade your audio experience with this premium case designed specifically for the ReSpeaker 6 Mic Array. This robust and durable enclosure provides a secure fit, shielding your device...

Flag holder for 22" yard flag. ...Printed for my kids during virtual learning.

Solidworks 3D model of my Blue Yeti USB Mic

mic arm base-Neewer, I use larger screws

Pioneer mic mountI lost mine so I created a replacement

Mic XLR to FX Send / Receive to XLR Out

Solidworks 3D model of my Blue Yeti USB Mic

DJI Mic 2 handle with tripod mount screw.

Remixed a headphone stand to hold an Icom mic

I've provided mounts for 35mm and 32mm poles (hopefully fits most monitor poles) and it will fit any mic that uses the standard 5/8" mic screw. Each hinge has adjustable tension so it will all stay where you put it.What you'll need:608 Bearings -...

... Chamber for Dice Storage. ...It adds a stylish touch and simplifies opening and closing the secret compartment seamlessly. Print Settings Resolution: 0.2mm Notes: A raft was necessary for the flag pole, but the flag itself can be printed without one.

It's designed to convert a single 5/8 inch adapter for a mic into a stereo 5/8 inch adapter for a mic. I highly recommend printing with 100% infill since it can easily break apart if not printed strong enough. However, 25% infill seems sufficient...

The mic holder printed best for me with the stud vertical and supports touching build plate. The fitment and assembly should be the same as the stock mount. There are 2 bases a short 200mm wide one and a narrower but deeper one. ...If you're using...

... the board without too big of a holder. I've used the universal hooks and printed the holder without supports. After I took the pictures, I've reduced the grip distance for the mic slightly (5mm vs 6mm) because the microphone was held a bit loose.

I made a microphone stand with spider that is cool looking and works very well :) There is 4 options for the spider : -cut in half (easier to print) with holes for metal nail (much stronger) -cut in half (easier to print) without holes -in one piece...

I have a Boya mic for my DSLR camera. It comes with a red clip that allows the mic to be attached to the flash slot of the DSLR camera, allowing easy recording while moving about. I broke that clip while removing the mic from it. These are 2...

A newer version of the mic arm addon for my AKG K7XX with my Sony ECMCS3 mic from my previous model: https://www.thingiverse.com/thing:2481074 This one is heavier but the mic is removable with the cables so I can take them off anytime and use the...

* Bendable design * 19mm opening * 1mm extrusion on the bottom which clips into the groove on the microphone, locking it in place * Front face chamfered for easier insertion * Screws onto the base of a regular mic clip. Pictures are PLA printed...

A newer version of the mic arm addon is available for my AKG K7XX with my Sony ECMCS3 mic, a design upgrade from my previous model. Check it out here: https://www.thingiverse.com/thing:2481074 This updated version is heavier but features a removable...

I designed this custom adapter for my NTG-2 shotgun microphone specifically to minimize handling noise that can travel through the included mount. It should work seamlessly with any shotgun mic that fits within the holder circles and isn't too heavy....

... the bracket in the factory location. The hole for the mic ended up being slightly small but a little heat from a lighter allowed it slide in.I printed with pla, no top or bottom layers and 30% honeycomb infill.This was for a 2010 Toyota Seqoiua

My church has two broken mic stand swivels, but I couldn't find a replacement part to order and it just seems wasteful to order new mic stands. So I grabbed my calipers out and started measuring. After a few hours in OpenSCAD, I was able to model a...

Mic Stand Cable Clip secures the cable to the small portion of a mic stand. ... Effectively attaches to 15mm diameter tubing often found in the upper section or boom of various mic stands.

Case with Cover for DJI Mic. Print in whatever color you need. IE: White for hiding it under the brides dress. Grey, Black or any other color for the groom. ... I printed with no supports but in the interest of esthetics you may want to print with...