mini board game card holder 3d models
755838 3d models found related to mini board game card holder.thingiverse
Customized version of https://www.thingiverse.com/thing:334172 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=334172
cults3d
Card Holder with double line for cards , each line with capacity for: 5 american standard cards or 4 Standard cards (MTG) or 6 mini american standard 5 spots for tokens large 277 mm width 50 mm height 19mm
thingiverse
For those who owned 2nd printing ROOT Board Game onwards, you only have 1 card holders instead of 5 Use this to print your own card holder Can be used for a general purpose card holders too! ... I designed this to be used with this great insert:...
thingiverse
Scythe Board Game Card Holder I reduced the mass of this card holder by about 100g: https://www.thingiverse.com/thing:3086696 I cut the sides open, added storage holes below the cards,and reduced the walls to 0.96 mm thickness. Printed at 0.32 mm...
prusaprinters
Scythe Board Game Card Holder I reduced the mass of this card holder by about 100g: https://www.thingiverse.com/thing:3086696 I cut the sides open, added storage holes below the cards,and reduced the walls to 0.96 mm thickness. Printed at 0.32 mm...
thingiverse
I am working to resolve this issue.** **A customizable card holder for your favorite board game!** The holder has a sloped bottom to hold cards in. A "finger" cutout in front allows for easy retrieval of the entire deck. Negative space in the floor...
thingiverse
This is a set of card holders for the game Dungeon!, the D&D board game. Instructions I've been sitting on this since Jan 2013 because I wanted to print it before I posed it. Alas I haven't found the...
cults3d
... the plastic blister that holds all the components. It is very possible that this card holder can also work for board games that use cards similar to the ones Takenoko has (4.5 x 6.5 cm), if you don't mind it having "Takenoko" written on it... ...:)
thingiverse
It is very possible that this card holder can also work for board games that use cards similar to the ones Takenoko has (4.5 x 6.5 cm), if you don't mind it having "Takenoko" written on it... :) ...
thingiverse
... lately so I decided to make a little something to make my setup and teardown of the game a little easier. ...This card holder was designed to be stackable, fit into the original gizmos box, and provide easy access to the cards during game play.
thingiverse
This is a card holder that I made to hold your draw deck and discard piles. ...This is made for NO CARD SLEEVES.
thingiverse
Card holder designed for Descent 2nd edition, but it will hold any 41mmx63mm cards. Printed on Prusa Pro with 0.2mm layer height. ...Enjoy!
cults3d
This is a card holder from Doc Seven's deck 77. The dimensions of the cards are 11 cm x 7 cm. The coin has a central hole underneath, to allow the player to push the cards out, all while being optimized to consume less filament. ... This way there is...
thingiverse
A smaller version of my other card holder, Scaled for the treasure deck in Talisman, Tall enough to hold all the treasure cards from the original box (Unlikely to hold any expansions) This has locating lugs so that they may be stacked. ...This has not...
thingiverse
Ideal for board game cards where you need to see the entire card like King of Tokyo. (playing with kids they need to often see their cards and read them) Fits 4 cards up to 65mm wide each. print as many as you need if you need to hold more than 4...
thingiverse
This a holder for the Orleans board game round cards
thingiverse
Just a little holder for the cards in "Dungeon! Fantasy Board Game". ...I printed a few of these and glued them on a board.
prusaprinters
Card holder for Wingspan, the board game. This remix reduces the amount of material by 9%, which saved about an hour on the print time. ...Make sure to print two of these.</p>
thingiverse
This is a lid to go along with MrPearson's "Gizmos Board Game Card Holder" (https://www.thingiverse.com/thing:3182483). ...It just snaps onto the top of the card stack, preventing the top layer of cards from coming loose in the box.
prusaprinters
This item was designed to replace original card holders from a board game called “Catan”, since original holders were slightly too small to fit play cards with newly installed plastic sleeves, see the last picture.Suitable for S-sized cards+sleeves...
thingiverse
This is a very basic card holder I created for the board game "Train Heist" (https://www.cryptozoic.com/train-heist). This holder fits well within the box and does not hold any other game pieces. This should be a pretty simple print, as it is just a...
thingiverse
Here are some of the card holders I have made so far for Horizon Zero Dawn Board Game. I have tried multiple styles of card holders with and without lids and finally settled on a card holder with a lid that slides into place. This will allow you to...
prusaprinters
This item was designed to replace original card holders from a board game called “Catan”, since original holders were slightly too small to fit play cards with newly installed plastic sleeves, see the last picture. ...Outer dimensions remains the same,...
thingiverse
These two racks are made to hold all cards of Awaken Realms Nemesis Board Game. The Small rack holds the green, yellow, and red cards on top, and the four types of crafted cards on the bottom. The large rack holds the remaining four types of large...
cults3d
... allow for easy card in and out. I printed four of these (plus 3 of my mini card holders) to hold all of the cards for Massive Darkness. ... These cards are standard boardgame size so should work great with any boardgame cards you need to organize.
thingiverse
... allow for easy card in and out. I printed four of these (plus 3 of my mini card holders) to hold all of the cards for Massive Darkness. ... These cards are standard boardgame size so should work great with any boardgame cards you need to organize.
thingiverse
BOARD GAME CARD HOLDER ========================= I remixed this piece because the original one was not fitting into my printer. Also, I felt like having a huge piece for playing board games is not ideal. So, I took this one, make a few changes and...
prusaprinters
I bought these dividers and did not want to pay extra for a 3d printed box, that has a hole in it, so that all the salvage cards would fall out, so I designed this box with a lid for easy transport.To fit all cards, you will need two boxes. The...
thingiverse
Couldnt fit the card holder on my ender 3, so just a simple split of the piece.