mining scoop 3d models

...I print mine scaled at 103% and the dimensions come out perfectly. UPDATE 2: Added new bodies for S2 vehicles (Evora 400, GT, etc.) as the plate light finisher is different from the S1s (the lights are set further back, closer to the bumper).

mine was doing great until i revisted it to try to shorten the key so an i sanded the top of the plastic piece flat an for some reason now it has to be held side ways at the ignition to get it to start everytime, with it in the case with the key its...

***NOTE: the LED array holder is quite loose and broke off mine after falling off a shelf, I would recommend strengthening this part with a glue or a lower print height to strengthen this part to prevent breakage*** **H MK3 cover (stl).stl & H MK3...

I have also glued a short strip of blue filament in the vertical slot to add a little color on mine. **UNTESTED BLTouch Mount**. As I don’t have a BL Touch, please send a picture of your make or let me know if there is an issue with fitting so I...

I cured mine outdoors, and did two coats on the whole thing, with about 15-20 minutes of cure time in bright sunlight, rotating periodically so each side would face the direct sun for at least a little while. After that, I slid on my silicone...

Most of mine seemed to have a good balance between friction to hold it in place, and ease of removal. Drag a sharp tool (e.g. ...a mini screwdriver or blade) around under the lip of the slide-in space to ensure there are no tendrils left that will...

I couldn't try it because I broke mine while taking the measurements! Leave me a comment if anything needs to be modified I preferred to make this support in 2 pieces to be glued with 2 centering studs to avoid removing the tedious supports after...

To make the carriage, you will need: a SG90 Servo A printed ServoLocker (mine was printed in SLA for maximum precision) a short piece of 2.85MM filament, I used PETG as it is what I had laying around two springs a printed servo holder a printed...

Mine is designed to print in the upright orientation without any supports (hence the 45 degree rise to the connection ring). I've also included some step-up/down adapters for tools with different sized dust ports, and the FreeCAD file so you can...

Here's what you'll need to build this fume extractor: * 2 x 60mm fans (mine are 15mm thick) + You can use either of these links - if you want ones that are only 10mm thick, it would make it easier to get the carbon filters in place, but that's not...

It attempts to simplify other designs out there for similar displays by using large, 3d printed parts to hold the diffusers, Custom PCBs to get the spacing right, and a laser cut back plane for ease of assembly. Things you will need: 20 PCBs - I got...

This will vary according to how tuned in the printer is so I can't guarantee that yours will stay on like mine. It is far easier to just slide the kazoo into this basic one and it can be done one handed pretty easily. this is the biggest benefit over...

I got mine from a knife similar to this. My knife blade got damaged, the tweezers and toothpick got lost and I really only used the scissors anyway. I took the knife apart to salvage the scissors and made this sheath to keep them safe in my...

36 - 53 cm for a LACK Enclosure (Mine were 46.2 cm long and they fit 5 normal spools with a couple inches of space to spare.) (7mm rod suggested by Mtractor1 in the comments.) 8mm works but it sticks a little when repositioning the bearings. 5x...

Minejust clear. Cable management: There are three pieces. One goes on the right hand side of the x axis gantry, but actually attached to the z axis roller bracket in this area. Normally the wiring goes to the left of the hot end but this now moves it...

For those with an action cam, if your mounts include a buckle like mine you can just use it, but I have also 3d scanned my buckle in so you can see it and perhaps print that as well. Future iterations may include a magnet to grab/replace in that...

I couldn't try it because I broke mine while taking the measurements! Leave me a comment if anything needs to be modified</li></ul><p>I preferred to make this support in 2 pieces to be glued with 2 centering studs to avoid removing the tedious...

 I printed mine in clear PETG, probably not a good idea as it won't work in brightly sunlit rooms.                  Connecting TubesOriginally they were designed so that the 6mm PVC fits over the tube.  However this caused too much interruption at...

Print I have printed mine on my LulzBot Mini using both PLA and ABS. You need to rotate the parts into place. The base is printed standing upright like it will when finished. No support needed. The top holder needs to be flipped in your software and...

I've included one stl with corner hold downs since mine kept warping off the build plate. The body contains a large bridge if you chose to print it without support. I suspect that some printers may not be able to do this ([you can try this...

I actually did mine at 100% with 0.1mm layer height (to ensure dimensional accuracy). The overhangs are critical, so I made sure I had a high % support, with a roof. You absolutely must get the overhangs flat. The pusher nub can be printed at 100%...

For example, it could take the drill to a rich mineral deposit for drilling/mining. Mars human - A human inhabitant for your base, the human has a suit on that protects him/her from the elements and hides his/her hands. Printer...

Either:My recommendation from McMaster Carr0.2lb ismore than enough force and won't squish your darts as much– more accuracy.Official 'nerf drum sprints' from foamblastbeware they have closer to 0.8lb (or more!) of force and may have issues with...

mine are sleeved with Ultra Pro Matte sleeves. I tried to create this so there would be as little wiggle room as possible. After all, this isn't the thickest box. However, the player pad by it's nature (since it's consumable) means that there is a...

- I did print all mine using this super cheap, strong, and easy to print Carbon Fiber PLA which makes the parts look as if they had come from the factory. - However, if you want a little more color, this <a...

I labelled mine as such: 1 2 3 4 5 6 7 8 9 Slots 1 & 3, 4 & 6 and 7 & 9 are the same just reversed. Slots 2, 5 and 8 are all unique. While there is some ability to exchange a couple around they don't fit well because of how some slots have chamfered...

For a better grip on the shelf I also printed mine with a filament-change 3 layers before the top doing the top three layers in a flexible filament to be squeezed against the shelf. The Rod The rod again is very simple - just a rod. The default...

It looks like it needs supports, but mine came out fine. 80% infill, 1 shell, .2mm layer height, using Ryobi green(ish) ABS is recommended for aesthetic pleasure, thermal resistance and overall part longevity. Once it cools, clean up the few strands...

The LED bezel is mine, the "C64Badge.stl" is here: https://www.thingiverse.com/thing:4218692/files, I just combined his "back" and "silver" files; and since I clearly couldn't duplicate the color stripes, I stole the rainbow flag from the gay rights...

Once printed, I hit mine with an air gun for a few seconds to clean up any strings. Take the nicest pegs you can and using one tiny drop of super glue put the peg in the slot and hold it snug in there for a few seconds. It's designed to line up...