mks tft32_l v4 0 3d models
603322 3d models found related to mks tft32_l v4 0.
thingiverse
This is a robust MKS GEN L board mount + fan mounts designed to fit any CR-10 and similar models. The goal was to craft a secure, adaptable, and solid mount for the board, especially fans and attachments, specifically for my standalone modification...
thingiverse
I made this to install MKS Gen L v2.1 in Tevo Tornado control box. The adapter is attached to existing mount points with 4x M3x4 and new board goes on top of it with another M3 screws. ...The mainboard is 2mm higher that original because of screws...
thingiverse
You can seamlessly integrate an MKS Gen-L Board into your existing stock case using this versatile adapter, eliminating the need for any additional drilling. ...The adapter was generously shared with me by a fellow member of an active Facebook group I'm...
thingiverse
The Mechanical Kit Standardization (MKS) Gen L Case features a 60mm fan cutout. ...Required components include: 4x M3 spacers, likely 40mm in length 4x M3 screws 3x M5 T-nuts for attaching to rails 3x M5 10mm screws 1x 60mm fan Access the Onshape CAD...
thingiverse
This adapter enables you to attach the MKS Gen L to your Ender 5. The cooling fan has been repositioned at a 45° angle towards the drivers, preventing it from obstructing long cooling fins of the TMC 2130. Requirements: Four M3 screws are...
thingiverse
For fitting the MKS GEN L to an Ender 3, I needed to extend the two cables for both thermistors and change the end stop connectors from 2-pin JST connectors to 3-pin JST connectors. To utilize the original Creality GLCD, use EXP1 on the MKS and...
thingiverse
UPDATE 21/04/2021 added cut files, for small 3d printers i have designed this control box, for mks sgen L v2 board, with mks ts35 display. It has space prepared to put a solid state relay for the bed and a mossfet relay for the hotend. It also...
thingiverse
I designed a custom mount for my MKS Gen L Board using Fusion 360 and was able to print it easily with minimal support needed only at the heater connections. To assemble it, I required some rods for the hinges, opting for long M3 screws in this case....
thingiverse
This is a detailed guide for the MKS Gen L case of Ender 3. When assembling, use M3 screws exclusively. If you'd like to suggest improvements, feel free to leave comments below. Consider showing your appreciation by donating an amount of your choice...
thingiverse
I required a holder for my MKS Gen L, only to discover that none had been designed yet. Frustrated by this lack of innovation, I took matters into my own hands. I obtained some small distance cylinders which I carefully screwed between the holder and...
thingiverse
Everything remains unchanged, except for the mounting holes that have been repositioned to accommodate the MKS_BASE-L board. Write your questions in the comments if you need clarification. ... If you enjoy this work and want to show support, a like...
thingiverse
This is a revised version of the MKS GEN L case, originally created by Michael at Teaching Tech. To improve durability, I extended the pivot rod, addressing an issue where lower-case pivots would frequently break off during printing. The modified...
cults3d
This is a remix of the MKS GEN L case that was made by Michael from Teaching Tech. I added a longer pivot rod because the pivots on the lower case kept breaking off when I printed it. The case is much easier to put together now without breaking the...
prusaprinters
This is a MKS GEN L board mount +fan mounts.It has been designed as a Tevo Tornado mod, but might fit to any CR-10, Ender and the likes. The idea was to create a solid, safe and as flexible as possible mount for the board and especially...
thingiverse
For my machine, I've mounted the whole assembly on the side of the printer and therefore have plenty of room to attach a custom panel with cutouts and mounted cooling fans.\r\n\r\nCAUTION: fitting the MKS Gen L with upgraded steppers may require...
thingiverse
So - I'm upgrading it to a MKS Base Gen L. This unit seems to fit in place quite well; I did need to re-route the extruder wires, but no big deal. Most of the connectors plug in. But I did have to replace the main power leads and mod the heatbed...
thingiverse
It's a case for the MKS Gen L board with ample space for cables and a hole for a 92mm fan. The fan is oriented to pull air, ensuring it doesn't blow over the printing area. With holes to attach the case to an EU2020 profile, this design caters to...
thingiverse
As for me, I've got my MKS Gen L up and running, so I made the decision to remove the slot for the SD card - it just wasn't doing anything for me, you know? And let me tell you, tightening up that USB port really makes a huge difference in terms of...
thingiverse
In this 3D-printer I used the following electronics: - MKS Gen_L V2 mainboard (with dual z-splitter); - DVR8825 Stepper motor drivers; - 2x Mosfet; - LCD 12864 RepRapDiscount full graphic smart controller; - 24V 15A power supply. This design is the...
thingiverse
Once printed the original base was just a tad short to fit my MKS Gen-L, so remixed and added 2mm in the width. Now fits like a glove. **Jan 12 2019** - printing now Going to add a fan so remixed the location of the Mosfet. MKS will be on top of...
thingiverse
I design this case for the MKS GEN L v2.1 because the original one integrated in the base frame of the OpenAstroTracker doesn't fit with the "AutoPA" and "Improved RA motor mount and tensioner" add-ons and TMC2209 drivers. I have added a miniature...
thingiverse
The user mounts the Gen L extruder to their Anet A8 3D printer.
thingiverse
I found that the in lower latitude versions of OAT, RA stepper motors clash with the bottom mounted MKS case. So, I designed a case that is mounted at the rear of the oat to prevent this issue from coming up in the first place, irrespective of the...
thingiverse
A case positioned strategically off to one side, leaving ample space for the X-car to fit comfortably within its confines.\r\n\r\nThe MKS board's assembly requires some finesse if you want to route the cables underneath as I have done; however, it is...
thingiverse
... giving you flexibility in its placement. The design also accommodates SKR 1.1 boards, which have the same dimensions as the Gen L board. A convenient USB hole has been incorporated into the design for easy connectivity. ... Date: August 16, 2018
thingiverse
Print settings: Infill at approximately 40% Print speed: 40 to 60 mm per second Layer height: 0.2 to 0.25 millimeters Check out my YouTube channel: https://www.youtube.com/watch?v=J5BzorV7rh0&t=240
prusaprinters
... the lines. Meshmixer says it's fine, while PrusaSlicer throws 16 errors. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: AmazonBasics PETG Orange Category: 3D Printer Accessories
prusaprinters
If anyone wants to improve on this design go right ahead Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: Doesn't Matter Supports: NoResolution: 0.3 Infill: 5% Filament: Geetech PLA Black Notes: Due to the size (or rather lack thereof) of...