mm jack 3d models
245016 3d models found related to mm jack.cults3d
this is a mold for you to 3d print and mold your own silocon 3.5mm jack Note: this is bigger then just 3.5mm
cults3d
After screwing and unscrewing a multitude of 3.5 mm jack nuts while building DIY synths, I designed a screwdriver-esque hand tool that should make the process easier and faster. No risk of slipping and scratching panels/chewing up the nuts unlike...
thingiverse
After screwing and unscrewing a multitude of 3.5 mm jack nuts while building DIY synths, I designed a screwdriver-esque hand tool that should make the process easier and faster. No risk of slipping and scratching panels/chewing up the nuts unlike...
thingiverse
This is my 3.5 mm stereo jack coating design, printed on my Craftbot+. It's designed for medium thickness cables so probably it won't work with very good quality ones. In any case I've uploaded the original .max model also in case you guys want to...
thingiverse
Under-table mount for a UGREEN branded 3.5 mm male to female headphone jack. It has very tight tolerances, so I used a clamp to squeeze the female jack into place. Scaling this up slightly might make for a better fit dependent on your printer. The...
thingiverse
Repair housing for 5,5 mm DC L connector. Glue both parts together with Loctite or hotglue. Funda para conector en L de 5.5 mm. Pegar las dos partes con Loctite o silicona caliente. ...
cults3d
Repair housing for 5,5 mm DC L connector. Glue both parts together with Loctite or hotglue. Funda para conector en L de 5.5 mm. ...Pegar las dos partes con Loctite o silicona caliente.
thingiverse
This is the 6 mm Tool for those little bolt... and Yes DON'T scratch the front panel! ;-). ...Print Settings Rafts: Doesn't Matter Supports: ...
thingiverse
Update 15 Sep 2017: Added 2 x 3.5 mm version after a request (Note: I used a different method for closing the back cover) [THIS VERSION WILL PROBABLY REQUIRE SUPPORT] I wanted to mount a headphone input underneath my desk near where i sit, so i...
thingiverse
Headphone holder for fix table top size ( 15 mm ) Audio socket is for 3.5 mm jack.
thingiverse
My stereo receiver was continually getting dust in the front headphone jack (which would then turn off the main zone). This is just a very quick 6.35 mm plug to seal that hole and prevent dust from entering. They are $4 for 10 on Amazon, but I...
thingiverse
This is a 3.5 mm headphone jack holder for corsair 5000d airflow computer case. It just clips into the triangular grating on case and loosely holds a headphone plug. I got tire of unplugging my headphones for a brief moment and having the cord get...
thingiverse
When replacing the stock audio cable with a 3.5 mm audio jack, this allows for a better fit into the casing, by tilting and retracting the socket away from the speaker system. To make the socket fit, the four notches on the plastic need to be cut...
prusaprinters
This is a little housing for the lightning to headphone jack adapter from apple, so you can protect the cable more from the daily usage, it fits together without the need of glue, but still you can use, for a better attachment to the housing, you can...
thingiverse
... that I cannot strap a [3D Hubs Marvin](https://www.thingiverse.com/thing:215703) to it. JaqLoopie is meant to solve this obvious design flaw. Plugged into any 3.5 mm stereo jack JaqLoopie it will hold on to your (light weight) phone strap charms.
thingiverse
The link between your device and these common portable credit card reader (used directly in the headphone jack) is usually very flimsy. How about printing a tight one for your device? This one is specific for the Samsung Note 8 tablet, using the...
prusaprinters
The link between your device and these common portable credit card reader (used directly in the headphone jack) is usually very flimsy. ...How about printing a tight one for your device?</p> <p>This one is specific for the Samsung Note 8 tablet, using...
thingiverse
Ich habe folgenden Halter für den Raspberry Pi an meinem Anycubic I3 Mega. https://www.thingiverse.com/make:527415 Mit diesem Halter kann die Creative Live! Cam Sync HD direkt in die Kopfhörerbuchse des Raspberry gesteckt werden und ist somit...
thingiverse
This is a supporter made for using Dayton Audio iMM-6 with my iPhone SE(2020). Please adjust the clearance gaps of two parts in the CAD data according to your 3D printing environment. There are holes for screwing, but I think you don't need...
thingiverse
These are 2 versions of a simple 6.4 mm audio jack/instrument dust plugs which you can use to cover up those unused jacks in your equipment. There is a version with a small handle which makes it easier to put in and remove and there is a version...
grabcad
This model is a standard 3.5 mm Mono TS Jack.Fusion360:If you want to make changes or link the model feel free to follow this link:https://a360.co/2Upmejl
grabcad
This model is a standard 3.5 mm Mono TS Jack.Fusion360:If you want to make changes or link the model feel free to follow this link:https://a360.co/2Upmejl
grabcad
It fits with stereo plugs, like headphone plug and Stereo Headphone Jack, or any 3.5 mm headphone. Gifs made with GifApp. Render made with Simlab Composer 6 and edited with IrfanView. ... The ZIM file can be seen on IOS and Android devices using the...
thingiverse
Remixed with Fusion360 Link: http://a360.co/2iN3Uf0 https://youtu.be/pYljJUUV3Sg