mobius dash cam 3d models
23799 3d models found related to mobius dash cam.thingiverse
This is a bracket to mount the Mobius Actioncam to the stalk of a typical rear view mirror. It uses a suspension clamp to clamp around the stalk. It'll work for different sized stalks by changing out the clamp to a different size. I recommend using a...
thingiverse
It is a Mobius cam holder that can be inserted into a bicycle light cradle.
thingiverse
Mobius cam mount Print Settings Printer: Wombot XL Rafts: No Supports: No Resolution: 0,2 Infill: 20%
grabcad
Full CAD of the Mobius cam, with internal components. Real and reliable dimensions (tolerance +/- 0.2mm). ...Formats: SW 2014 / STEP / PARASOLID
thingiverse
Protection for Mobius Action Cam to play airsoft. ...It is designed for a glass 20 mm in diameter, with a thickness of 4.8 mm.
thingiverse
3D Printable case for a Mobius Action Cam. Can be retrofitted to any number of devices, mountain bike, surf board, UAV etc. If you like this model then give it a like. If you like our design and would like to build it so that it is as strong as...
thingiverse
2 axis gimbal for mobius camera for 0.4 mm nozzle EASY to print without support
thingiverse
I designed a dash cam support to be mounted on the inside mirror. ... i used the ball joint and the nut from the dash cam parts.
thingiverse
This is a conversion kit to turn your Mobius camera into a 3D-stereoscopic camera for mounting on a FPV Racer (First-person view quad-copter) or an Aerial Photography RC Aircraft for filming 3D aerial videos. The AUW is 70g which means you could...
thingiverse
So I designed this simple bumper scaled to fit the mobius perfectly both original and wide versions. Shouldn't ever happen again! ...:) Instructions print with supports 0.05mm overhang is what i used...
thingiverse
I needed a mount for my dash cam because the suction cup was messing up my windshield tint. I would print this out of PETG or similar due to the heat. PLA+ works but gets very soft. ...I used 3M double sided automotive tape to mount it.
grabcad
This clip allows you to mount a dash cam to the passenger sun visor. You will require an M5 20mm cap head bolt, washer and nyloc nut. The nut in the picture was machined for the purpose, note the camera fitting is tapped M5 so the cap head bolt is...
thingiverse
Link For Dash Cam Kit I Used: https://www.amazon.com/gp/product/B07DGS11CM/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 Link for Mirror Mounting Bracket:...
thingiverse
The dash cam I printed these for uses a Mini USB cable, which is a bit thicker in size than most Micro USB cables. If your dash cam uses Micro USB cabling or any other type that is not the same size as mine, you may want to scale this print down a...
thingiverse
These are meant to sit on your dash and face sideways, to help you see around corners for traffic. The camera mount was designed to fit in the corner of the dash against the windshield of my 2000 s-10. I made these out of abs and have 1 of them...
thingiverse
This bracket is a better design for the SJ1000 Dash Camera that allows you to see the screen through the bracket. Instructions Print with support. ... Remove the Plastic camera holder from the belt...
thingiverse
- Xiaomi Yi Smart Dash Camera mount - Didn't want to remove original mount from my car when I traveled abroad and wanted to use the camera in rented vehicle... ... - Printed in PETG, 236C, 100%infill, 25% fans - Use thick, double sided tape to stick it...
thingiverse
This is a mount for a standard, cheap [yi cam](https://smile.amazon.com/dp/B01CW4ASS0) Simply wedge this up by your rear-view mirror and run a long [usb cable](https://smile.amazon.com/dp/B073PT6Q1P) around your windshield
thingiverse
My holder for the cam broke, printed a replacement mount with petg but the sun melted and deformed the piece. So made this to hold in place even with sun exposure. You have to cut the holder of the original holder. ...Mine was already broken so had no...
prusaprinters
Got tired of the cam constantly falling down as no sticky tape/pad would stick to the plastic cover on the boot lid “roof”.In the end I decided to make a simple mount that hooks on the plastic cover and keeps the camera in place.Printed with PETG to...
grabcad
1:1 scale of Mobius action cam - lens C. I measured all dimensions using a caliper, so I guess tolerance are within 0.5 mm. I also included a model of Mobius mount. ... Available files format: Solidworks 2014, STEP AP214 , STL
thingiverse
This is a bracket to mount a Mobius Actioncam to the rear view mirror of C6 Corvettes. It removes the cover in the front of the stack and uses a zip tie or similar through the mirror to keep it from moving. This keeps the camera out of the drivers...