mod your ps3 controller 3d models

I warmed up the butterfly on the wings and bent it a bit, this creates a 3D effect. You could do many things, for example eyes that look at you in the dark, swap ornaments and symbols depending on the season or festival and holidays, when the child...

To prevent the duct from leaking and causing drafts over your print I recommend lining the x-carriage with some sponge rubber. And this is the only thing you need except from the fan and the duct. Oh: and some tape or foil to cover that big hole...

Edit it online if you need any tweaking for your sensors. https://www.tinkercad.com/things/2neqPEmkfyT This is a project that marries 3d printed Items (Base and Mount) with already available items (Pie Tins) to create a Stevenson Screen. To a...

If yours are taller you will want to make these rods longer.2 - 1/4” 20 pitch screws ~1” long that are used to lock in the height of the assembly20 - 8 x 3 mm magnets. I purchased mine from amazon. This is threaded with 1/4” 28 pitch threads that the...

Japanese Mask The Deep World of Noh - Noh Mask Halloween Cosplay Mask This is just the STL files to be able to print your own mask on a 3D printer. The mask is ~280mm high,~181mm width and ~79mm depth. This mask can be scaled to fit smaller heads. I...

Pitch Diameter: three inch Outside Diameter : 3.125inches This third set in your inventory comes out at size roughly four with its larger counterparts being five. Spur Gears They also have different tooth sizes - here is the full specification for...

If that happens, apply pressure on all areas of the beam and push down. Repeat steps 12-14 with the second beam and baseThis is what both parts should look like when they are completed STRINGING IT TOGETHER:Start by getting 3 pieces of 54 cm fishing...

This can be done as a single job with multiple copies of the object.Finishing and AssemblyAfter printing, test fit your Forstner bits and flexible inserts to make sure everything fits properly. Flexible inserts should simply pop in to place and be...

But to really appreciate the Aon Center, you have to walk right up to it and crane your neck to see the top. Fortunately, this is possible thanks to a sunken plaza in front of the building with some rather extensive fountain work. This creates an...

Note that some trial and error will be necessary to make it match to the severed neck stump of the kitty; your mileage may vary. Work in progress. StabbyMMScalp: Making this a separate piece allows for easier cleanup of the mask, placing the...

Since this was only open from one side, a solution was needed.The solution was a 200mm diameter hole saw, Fusion 360 and the 3D printer.At this point the note:According to the competition rules, I have to point out that there will be a loss of...

Join me on this unforgettable odyssey through time and space; within these sacred sands lies an enchanting secret, just waiting to be discovered by your very eyes. Each moment is imbued with wonder, every carefully crafted poly telling a story of...

The lower upper link mounting position should keep stock geometry, the upper upper link mounting position should give you a little bit of link rise and keep your pinion angle the same.The link slots have been designed for Revo rod ends, which have...

My personal favorite settings are the default values, however your mileage may vary so don’t hesitate to play with the values of the customizer. With all the settings fine tuned it was time to find the right color combination. Of corse black and...

Print Settings Printer: Monoprice Select Mini Rafts: Yes Supports: No Resolution: .2 Infill: 20% Notes: Rafts may not be needed depending on your printer. Mine does not immediately begin extruding when it begins printing, so I must use rafts to...

Please leave your comments on this design. And I hope you find it helpful. ============================================================= Это мой вариант конструкции головы для FlyingBear Tornado2 (T2). Я назвал его OpenHead не только потому,...

Take your time to align them properly.The Screw holes are just hanging in there! ...That can't be safe!</strong><ul><li>The Screws are just there to align the set and keep the layers within the bearings from shearing off.</li></ul></li><li><strong>If...

I also painted the handle blue because the LED I used in this example is blue, and once you use it for LightPainting it's essential to see what color your tool has without it emitting any light. Custom Section Needed vitamins In addition to the...

This year, impress your friends and family with this cutting-edge Easter technology. Yes, this limited edition, Easter Bunny-approved 2016 3D printed Easter egg has not 1, not 2 but 4! Yes, 4 moving parts! But wait, that's not all! Order now and get...

How are you going to approach your story book? In my case, it has been a healing process. Cuentos Perdidos is a selection of several stories that I have written throughout my life. They are stories that I have written in different moments of my life,...

... few <b> 8 mm ID o-rings</b> are handy for adding friction to when needed. <b>Last thing:</b> I plan to extend the set of components in the future. In that way I'm also open to your suggestions. ...And I'm also looking forward to you creations :-)

...If they don't light unscrew the battery holder bottom, remove the battery, push the cake top out via the four slots in the cake base's bottom and check your wiring. Enjoy! I include the OpenSCAD source file. It is still a bit of a mess, sorry.

You can mount any of these boxes right to a din rail, or sandwich a gopro mount between them so you can aim your box up or down. I redesigned the din rail clip so it’s stronger now, and fits a 35mm din rail a little better, and it is easier to...

Aluminium tube: 3,2mm outside diameter, or some other diameter of your choice, it's just to enlarge the input and output holes to fit another size. When you have printed the parts, it's important to get smooth surfaces so use a fine grit sandpaper...

Share your makes, and what you decide to grow in the planter. I am going to move it from experimental, to "finished." Print Settings Printer: Folgertech FT-5 Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% Notes: I printed it with 3 shells...

christmas tree with decorations called "chrisbaum" Print your own christmas tree "chrisbaum", which you can decorate with balls, jewelry and candles. There are two versions: 1) 3D printing version In this version, everything for the tree can...

I have provided the source code for download, so you can adjust the design to your needs.Happy printing!If you like this design, then please leave a like and also post a photo in the comments.Looking for more Tefifon related stuff? ...Have a look at my...

... If that happens to you, you can print any of the BOXes on 0% infill and you can rest assured that your filament won't snap (hopefully). ...If you do go that route, I recommend using 3 perimeters.</p> </div></p></p></p></p> Category: Games

This project creates a fun toy/craft to help illustrate the forces of lift, and principles/physics of flight.&nbsp;To 3D print the parts it is recommended to have your Z height down fairly low. This should result in the first layer fully squishing...

You will want to use some sort of super glue (or appropriate glue for your filament of choice) to hold it all together. Step Wall Options 2 Step 3 Step 4 Step 2 Step - Vallejo/similar Bottle Height Wall-Mounting Wall Options 1 Shelf Wall 2 Shelf...