mods for monoprice 3d models

This is a DIY project for the Monoprice Modern Retro headphones that enables detachable cables. I used panel mount 3.5mm jacks and some Ethernet cable wire to make this modification. ...The example in the photos has been sanded and painted, but you can...

This is an upgraded fixture and nozzle designed specifically for a 50mm blower fan, offering enhanced cooling capabilities compared to the standard 40mm radial fan used on the Monoprice Maker Select Plus. As a work in progress, I'm currently...

I designed this project specifically for my Monoprice Maker Select printer, but it has potential applications in various settings. With this setup, I can easily switch between printing on the build tek surface and glass while ensuring the nozzle...

You will need supports for the AC plug/switch unless you possess incredible bridging abilities. If you enable supports everywhere, don't forget to remove them from around the chamfer near the fan screw holes. I printed an earlier version that...

... rubber foot. Print Settings: Printer: Monoprice Maker Select Rafts: None Supports: None Resolution: .20mm Infill: 30% Notes: Since this part doesn't require the same strength as the main components from the Azza mod, I used 30% infill.

Cap for monoprice modern retro headphones to make the cable detachable. You can also use it to make the headphones balanced by using the cape for both sides of the headphone. It uses...

The stock fan was too loud for my liking, so I replaced it with a 120mm PC fan. ...to allow for sufficient airflow those feet will lift the printer 35mm + 5mm if you add some cork underneath it. ...I attached them with hotglue.</p>

If you installed your Z-Brace mod on your Wanhao, MP Maker Select, or other similar 3D printers, you probably noticed that the gantry feet no longer touch the surface where it sits. These pads fill in the gap to provide extra stability. ... Print...

Here is an experimental design I made for my Tina 2 3d printers. ...The back one takes a plate of 1/8th inch acrylic or glass, meanwhile the front is more open to allow for the front window to be connected with 6x3mm magnets.

After I printed out Monoprice Select Mini SD Card Extender Holder-mod (https://www.thingiverse.com/thing:2357466) I soon realized I had bought a MicroSD extender not SD LOL So I made this adapter since I had already printed out the SD one. ...Print...

After printing out the Monoprice Select Mini SD Card Extender Holder-mod (https://www.thingiverse.com/thing:2357466), it quickly became apparent that a MicroSD extender had been purchased instead of an SD card holder. ...Laughing at my mistake, I set to...

After I printed out Monoprice Select Mini SD Card Extender Holder-mod (https://www.thingiverse.com/thing:2357466) I soon realized I had bought a MicroSD extender not SD LOL So I made this adapter since I had already printed out the SD one. Print...

After designing and building the Z-brace mod for the Monoprice Maker Select Plus, as described on https://www.thingiverse.com/thing:2349318, it became clear that side feet adapters were necessary for the column braces, since the original design only...

Extended legs (creating more space for stuff and improving airflow) 2. Snap-in sidewalls for expansion space 3. New bottom cover with a finned fan mount, better airflow, and lower sound level 4. A/C converter pocket & wire managers 5. Raspberry PI...

I'm excited to show off my Monoprice Maker Select V2, which boasts an impressive array of mods that significantly enhance its performance. Among the notable upgrades are the z-brace mod, the Dii Cooler mod, and my own innovative Smooth Spool Holder...

I specifically wanted a dual-color Z-brace mod for my Monoprice Maker Select, so I used Azza's original file and duplicated the "balls" to achieve my desired effect. ... The "balls" can also be utilized for the "Plus" versions of these printers, leaving...

Store a small cabinet for essentials tailored to your preference.

Here are a few mods for the BNB SX extruder. 1) Revised lower clamp with cable support - This is designed to prevent binding when the extruder is on the right-hand side. The normal Bear/BNBSX extruder has its cable support connected beneath the...

These upgrades are available for the revised Buccaneer model. ...Additional details may be discovered on the webpage reprap.org/wiki/BucSid

The part fits the 3d printer from Monoprice MP10. With this part, the filament spool is kept straight and unwound cleanly. ... It can be used for different spool widths

These brackets plus an 18 by 22 inch piece of plywood, along with standard zipties and screws, significantly enhance the portability and stability of the Monoprice Prusa 3D printer. ...My photos showcase a felt wrap and additional holes in the plywood...

Display Frame for Monoprice MP10 is a high-performance display that offers superior brightness and color accuracy, making it ideal for professional applications such as graphic design, video editing, and photography. ...With its advanced LED...

This bearing spindle was designed specifically for the MonoPrice 3D printer. To assemble it, you will need a 4-inch bolt, a flange nut (simply grind off any remaining spurs) and two high-quality skater bearings. ...Once assembled, slide the spindle onto...

... Update: Version 2 of the Printer foot eliminates the need for any supports. Print Settings: Printer: Monoprice Select Mini Rafts: Irrelevant Supports: Essential Resolution: 0.175 millimeters Infill: 20% density

This mounting bracket allows you to attach Monoprice spools on either top-left or top-right area of your Mendel-style RepRap. To use it, print at least one Spool Mount and two or more Connectors. An M4 nut/screw is needed for each connector. ...Please...

Calibrating the Monoprice Maker Select 3D Printer's Bed Leveling System. ...Begin printing and fine-tune the bed height in real-time, making adjustments as you navigate the outer edges of the build platform to achieve flawless leveling.

This is a spool drawer that fills 1/4 of an emptied spool of Monoprice brand filament. Getting the parameters right took a few tries so I thought this was worth publishing. Print 4 of these and it'll fill the spool. Customized version of...

This is a custom-designed spool drawer that perfectly fits 1/4 of an emptied spool of Monoprice brand filament. I had to make several attempts to get the parameters just right, so I thought it was worth sharing with others. To fill a standard spool,...

A maker opted for a customized Monoprice Ultimate Spool Holder design, scaling it down to accommodate the smaller voxel filament spools.

This project is still in development (V1 untested) 15-April-2019 I corrected some missing levels icons on the TFT and added an emergency stop feature to the custom menu for use with Octoprint. 3-April-2019 I moved the MKS Main Board up by 4.2mm so...