monoprice maker select 3d models

... to the side of my frame using double-sided tape. Keep in mind that the LEDBERG operates at 24v, so you might be able to power it directly from your Maker Select PLUS model's power supply, but standard models with their 12v supply won't cut it.

... I ran it along the seam top and bottom. The guide wire length can be adjusted; simply push them in place and use a hot iron to cut and score them, securing them firmly. This is just a prototype, but it functions well on my Maker Select machine.

... Print Settings: Printer: Monoprice Select Mini Rafts: No Supports: Yes Resolution: 0.175 Infill: 25% Notes: Print with build plate supports, with the flat side facing down (the side that normally touches the heat sink against the build plate).

I've successfully printed flexible filament with my Monoprice Select Mini V2 after numerous attempts. Frustrated but not defeated, I searched the Thingiverse community for a solution to my feed plate woes, specifically designed for the MP Select Mini...

This is a longer replacement end cap for x-axis rods on the Monoprice Select Mini. Designed to provide extra space, it features a slot that allows pulley assemblies to slide in smoothly, making belt tensioning possible without spring or other...

I was approached about excellent calibration prints for the Monoprice Select Mini, and beyond the standard (Benchy, etc.), I stated that all I use is a first layer test, since most of the time that's the majority of the struggle. Couldn't attach the...

This is a remake of USWaterRocket's E3D V6 mount for the Monoprice Select Mini. https://www.thingiverse.com/thing:2353376 Since I don't have an extra E3D V6, I re-designed it to work with the stock Creality hot ends and Microswiss hot end. I also...

Print Settings Printer: Monoprice Select Mini\nRafts: No\nSupports: No\nResolution: .2\nInfill: 100\nNotes: For the Pi case, I used 0.4 walls or 1 shell, then 100% infill to prevent hollow spots along the case walls.\nTo build the mount, you can use...

... and ensure a smooth fit with 1.75mm filament before installing. This printed very cleanly with minimal rework required using PLA. Print Settings: Printer: Monoprice MP Select Mini p/n 15365 Rafts: No Supports: No Resolution: z = 0.0875 Infill: 100%

... hole and guide slot to ensure a smooth fit with 1.75mm filament. Print Settings: Printer: Monoprice MP Select Mini model #15365 Rafts: None used Supports: Not required Resolution: Z-axis resolution set at .13125 Infill Density: 100% solid infill

This Y Belt Tensioner for the Monoprice Select Mini (Malyan M200) Y Belt was inspired by https://www.thingiverse.com/thing:2209231 and numerous other GT2 belt tensioners on Thingiverse. I was dissatisfied with variations that necessitated printing...

Another creative solution for attaching a PiCamera to your Monoprice Select Mini printer involves repositioning the camera to minimize visual obstruction and conceal the cable. By relocating the camera, you can avoid blocking the view from the front...

Decided to upgrade the hot-end fan of my Monoprice Select Mini V2. Unfortunately, the Noctua NF-A4x10 PWM I ordered needed a capacitor to get it going, otherwise it would if the hot-end climbed higher than 70C; an online search revealed I need to...

This replacement fan shroud for Monoprice Select Mini printers offers superior cooling to printed parts and heat break, making room for the mounting of a 40mm fan. Designed specifically to work with m4 bolts, this model ensures that any 40mm fan...

This bracket serves as a holder for the Bowden style E3D V6 heat sink/hot end on the Monoprice Select Mini printer. Its dimensions ensure that it remains at the same level as the original heat sink, eliminating the need to adjust the z-axis limit...

This design is heavily influenced by "Print Head Dual Fan Adapter v2 for Monoprice Select Mini," but has been completely revamped to fit perfectly onto a Micro Swiss full metal hotend. UPDATE: I have added two stabilizer beams to provide maximum...

I was reached out about good calibration prints for the Monoprice Select Mini, and beyond the usual (Benchy, etc), I mentioned that all I use is a first layer test, as most of the time that's most of the fight. I couldn't attach the file to a...

The feed base broke near one of the screw holes on my Monoprice Select Mini and I tried using the model released by cmniemann, but it didn't work with my printer due to several alignment issues - most notably the spring mount. This is my mod on the...

This is a replacement mount for the Monoprice MP Select Mini V2 X Min Stop switch. This allows removal of the X Gantry affectation.</p> <p>My belt was getting too loose. So, I read and drank, drank and read. What I determined, based upon my reading...

I wanted to try a Y axis mounted camera for my Maker Select V2. I had the "Raspberry Pi Camera Case and Mount for Mini Kossel" already printed out but I didnt like how flimsy it's mounting arms and back were so I drew this up and mounted it to the Y...

It uses this cord: https://www.amazon.com/gp/product/B00L9UGACW/ref=oh_aui_detailpage_o00_s00?ie=UTF8&amp;psc=1 and two disk magnets 3/4" x 1/8". EDIT: Magnets are more like this: https://www.kjmagnetics.com/proddetail.asp?prod=DB2 Also added a STEP...

This is a straightforward filament guide for the Maker Select v2 designed to work seamlessly with the spool holder turned 180 degrees so that the spool rests on the right side. It attaches to the outer two of the four screws located in the top right...

I was looking for a Z-brace kit for my Maker Select v2 and found one here by f0xox that looked simple enough and wasn't overly complicated: https://www.thingiverse.com/thing:3603327. I loved the design by f0x0x but when I printed it and mounted up...

The channel is the same height off of the table so it should work fine with the other feet.Since I mostly just want to eliminate the annoying rubber feet that come with the Maker Select v2 and fall off all the time, I print these out in PLA and add...

It uses this cord: https://www.amazon.com/gp/product/B00L9UGACW/ref=oh\_aui\_detailpage\_o00\_s00?ie=UTF8&amp;psc=1 and two disk magnets 3/4" x 1/8". EDIT: Magnets are more like this: https://www.kjmagnetics.com/proddetail.asp?prod=DB2 Also added a...

I was examining the filament release lever on my Maker Select v2.1 just a few days ago and observed that one of the sides of the filament insert hole had become misshapen - it looked as though constant friction from the filament against it had worn...

The following settings were employed: Quality Layer Height: 0.1 mm Shell Wall Thickness: 0.8 mm Top/Bottom Thickness: 0.8 mm Infill Density: 20.0 % Material (Note: Used for PLA) Printing Temperature: 195 C Build Plate Temperature: 50 C Diameter:...

The following settings were utilized: Quality Layer Height: 0.1 mm Shell Wall Thickness: 0.8 mm Top/Bottom Thickness: 0.8 mm Infill Density: 20.0 % Material (Note: Used for PLA) Printing Temperature: 195 C Build Plate Temperature: 50 C Diameter:...

MINIMONOPRICE The Mini Monoprice Mini To learn 3D printing and modeling, I'm making a 1/3 scale model of my Monoprice Select Mini, which is my first printer. I recently bought it and love it so much! I started creating this miniature to eventually...

A simple handle to help prevent burning finger tips while moving the build plate. I saw there was a few handles available for the stock Y carriage but none for the upgraded Y carriages like the one I use, Gulf-coast robotics (the one with the...