mosquito hotend adapter for e3d v6 mount by

I was able to attached my mount to new E3D v6 Carriage that I remix https://www.thingiverse.com/thing:2659436 but I add to drill new hole in the middle ( and the upper hole was break ( but it is not in use any more ) , I will update this part with...

I successfully attached my mount to a new E3D v6 Carriage that I remixed from Thingiverse, where the ID is 2659436. However, I had to drill a new hole in the middle because the upper hole was broken - it's not needed anymore anyway. I'll be updating...

I upped the diameter for the E3D V6 so now it fits perfectly with both extruders snugly attached to the main board of the printer! This design now works seamlessly. ...Here are the print settings: Printer Brand is LulzBot and specific model TAZ 4, no...

... deformed at the end due to heat from the heater block. FYI 2: This printer uses E3D hotend components (heat sink and heater block), not the E3D upgrade parts from DreamMaker. ...The heater block from DreamMaker appears larger, so results may vary.

I upgraded to an E3D V6 and made this mount and part cooling duct for it. I've been using this design for several months now. The only thing that is relatively new is my using of printed bushings and the bushing holders I made. The part cooling duct...

Modified from Thingiverse's thing:559657, this extension boosts E3D-V6 to almost equal the original Printrbot hotend length. It securely attaches to the hotend using 2 4-40 screws. However, a minor adjustment is needed on the hotend - it must be...

Remix of the previous design to compensate for slop in the V6. The previous design held the V6 in place with one screw, which meant that the V6 heatsink had a greater Mechanical advantage on that part than it should have, resulting in the V6 being...

... After building a lightweight fan for the stick extruder, I created one for the V6 Clone with a matching mount. The bracket fits on the stock cart and is compatible with my LRU conversion. Two 40x40mm fans can be installed, each up to 20mm high.

Human: Dual E3D Mount for Ultimaker. ...OpenSCAD Files Included for Customization Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Extended Rafts: None Supports: None Resolution: 200 Microns Infill: 20%

https://www.thingiverse.com/download:6180436 # Update 10/25/2019 -Updated BLTouch Offsets define X_PROBE_OFFSET_FROM_EXTRUDER 27 define Y_PROBE_OFFSET_FROM_EXTRUDER 4 define Z_PROBE_OFFSET_FROM_EXTRUDER 2 # Update2.1.1 -Made mounting holes larger...

I'm really pleased with my e3d V6 carriage mount for duplicator / ctc setup - it's been working fantastically well so far. One of the main benefits is that the motor & drive block isn't sitting behind the heatsink, which means it stays cooler...

This is an add-on to this item: http://www.thingiverse.com/thing:1570168 With this adapter plate, you can use this thing: http://www.thingiverse.com/thing:1620630 for cooling purposes. [UPDATED] I've upgraded the design to make it more visually...

... it loudly. I like my prints nice and tough. As for mine, I got great results printing at a .3951 layer height. Yes, you read that right – very thin layers make all the difference with an E3D Lite6 nozzle paired with the awesome Volcano .6.

It attaches to the front half of the clamp commonly used to hold an E3D V6, making installation incredibly easy without replacing other parts. The starting point was Tech2C's clamp found at https://www.thingiverse.com/thing:1752766. A 40mm bed...

Printed the original, but am guessing that its meant for use with an original e3d v6 and/or Titan - it doesn't fit very well with my clone e3d v6 or my clone Titan extruder. As a workaround I have shimmed the neck with a small piece of sillicone. My...

Printed the original but think it's meant for use with an e3d v6 and/or Titan - doesn't fit well with my clone e3d v6 or clone Titan extruder. As a workaround, shimmed the neck with a small piece of silicone. ... My changes to Marlin configuration.h to...

... etc.) or the heater block directly. Originally, this issue was largely mitigated by the fan's position above the upper mounting flange of the heatsink and below the top of the heater block, effectively eliminating potential contact points.

Here's a simple e3d mount that requires just 2 m3 bolts and nuts, I use a combo fan similar to this one (https://www.thingiverse.com/thing:839620) but anything designed to snap onto the e3d system should work like this one...

this is a simple e3d mount requiring 2 m3 bolts and nuts, i use a combo fan liker this one (https://www.thingiverse.com/thing:839620) but anything designed to snap onto the e3d system should work. like this one ...

Ender 2 users now have a simple solution to upgrade their machine's print quality - a sleek and reliable hotend mount designed specifically for the Creality Ender 2. ...This innovative accessory secures firmly in place with sturdy M3x30 screws, ensuring...

My hotend has a bigger push connector, so I enlarged the hole and added some extra material to the sides to make it more robust. Print Settings Printer: The Prusa i3 Clone with He3D is my go-to printer. Rafts: I skipped adding rafts to this print....

Remix of https://www.thingiverse.com/thing:5222458 by richgain. I use a volcano without part cooling much of the time. This clamp is simply a cut down version of the original. ... Use the original v6 fan

Remix of https://www.thingiverse.com/thing:5222458 by richgain. I use a volcano without part cooling much of the time. This clamp is simply a cut down version of the original. ... Use the original v6 fan

... ear-piercing noise and relentless operation. ...In an effort to address this issue, I've developed a custom adapter for the 40mm fan, which boasts significantly lower decibel levels and an impressive durability advantage over the standard 30mm unit.

I recently discovered that the stock setting for the BLTouch is situated significantly beyond the hotend. ...To rectify this issue, I have modified the Marlin script to adjust the BLTouch's position according to the following coordinates: X: -19, Y:...

The main idea behind this design is to allow users to quickly swap out tools by simply loosening two screws, then mounting the hotswap mount to the MGN12 rail without needing to recalibrate the system. This means that users can easily switch between...

A miniature inductive sensor mount is available for a comprehensive all-in-one fan duct system with a diameter of 12 millimeters. ...This small component can be found at the Thingiverse website, under the identifier "1292038".

Thanks to Hevtec for his whole work with the videos and parts! ... Melt in two M3 threaded inserts. BLTouch can be height adjusted Use this BLTouch Mount: https://www.thingiverse.com/thing:4740161

Mounting the E3DV6 on Anet Printer

Remix for Tronxy X5SA Pro: - Shifted screw hole to the left position - Eliminated material to facilitate belt insertion on the right side Cooling fan mounts seamlessly with a hot glue gun... ... Scaling may be necessary, ideally 10% (Fusion 360 appears...