mounting vive sensors 3d models

Used for mounting a run out sensor to the FLSUN QQ S and allowing to follow the filament as it comes off the spool. ...Handy tip if your wiring supplied with the sensor is to short you can purchase a fan extension cable to extend bought on Amazon here...

Hamamatsu G11508, G11475 to G11478 InGaAs linear image sensor https://www.hamamatsu.com/resources/pdf/ssd/g11508_etc_kmir1032e.pdfG11508-256SA, One-stage TEC, 256-pixels, 50-x500-um pixel sizeG11508-512SA, One-stage TEC, 512-pixels, 25-x500-um pixel...

This is a slide-in bracket that houses 8 Hall sensors and an Arduino Pro Micro. It completely replaces the electronics module of the Fantec Clubsport shifter with 8 system joystick buttons, one for each gear. This design has been working perfectly...

I've constructed a full-size model of my miniature Stevenson Screen. ...This enlarged rendition comes in two height configurations and offers not one, but two distinct mounting solutions for the utmost convenience and versatility.

The datasheet for the flow sensor can be found here: http://www.digmesa.com/wp-content/uploads/932-952x_Bxxx_GB_20V-2.pdf This base features 2 countersunk holes and a flat base for mounting, which can be secured with a single screw or double screw,...

This design uses a commonly available endstop module as a sensor, such as this one: https://amzn.to/2GYdmtL The 4mm outer diameter, 2mm inner diameter PTFE tubing I'm using is standard and widely available: https://amzn.to/2E7HKyX It's connected to...

The front end of the car features brackets for placing a light sensor and RGB LED modules from SAM Labs, which can be programmed to react to varying light conditions. There are three wheel sizes and the vehicle body in this project. Print Settings...

... percentages. I damaged mine slightly, but there's no need to overtighten. Larger sensor appears to be attached using two-sided tape as well, indicating that a custom mounting bracket may be necessary once it detaches from the door/window frame.

For my purposes, I made a few changes: - added places for screws to close the cover - M3x0.5 x10mm metric threads - extended canopy - additional fixing for the screw - chamfering the holes for the tapered screws - solid cover to be screwed on -...

Problem is, I could not use them because that requires the sensor mounted perpendicular and this wasn't effective. There are no keyhole slots on the angled side so it was either wait until I could go buy some double-sided tape or design this...

Updated: 8/16/2021 - Added version two file to add screw holes for attaching the cover to the filament sensor and mount. I purchased a Creality Filament Sensor that was recently included with the new Creality CR 6 SE. I was trying to find a way...

Reuse your Vive deluxe audio strap headphones/speakers on your quest pro. Actually, you can probably zip tie this to any headstrap. You'll need to print one normally and print one mirrored. The C-shaped groove should face rearward when mounted to...

## Extending Connectivity for Oculus Rift This innovative mounting system is designed to extend two of the four Oculus sensors, with the central mounting block engineered to fit two of CableCreation's high-speed USB 3.0 Extension Cables...

Revised version of my Arduino sensor mounting plate redesign now features four pillar holes for easy installation and additional side mounts allowing multiple plates to be connected together seamlessly. Print Settings: Printer: Prusa I3 Rafts: ...

This is the mounting flange for the BLTouch Auto Leveling Sensor (see link below) that can be used to mount the sensor securely. The OpenSCAD file is included so users can design their own custom mounting systems easily. The STL files aren't as...

This is a 3D printable mounting bracket for a HiLetgo HC-SR501 PIR Infrared Sensor. ...Printed with ABS.

This is a 3D printable mounting bracket for a HiLetgo HC-SR501 PIR Infrared Sensor. ...Printed with ABS.

This is a adapter from Vive Pro 2 Lenses from VROptician to Pico Neo 3 Link

The HTC Vive cable needs to be fixed so it can fit under the table properly.

This is being written in Feb 2021.) but it will probably have a backwards compatible camera mount, like the Vive Tracker. But the real potential will be to remove the camera mount and heavy bolt, and screw directly into the tracker like another...

Mount your BIQU Filament Break Sensor to your Voxelab Aquila FDM printer! Yep, it's a simple design and I figured I'd share it. ... :)

A 3-D printed mounting bracket is designed to support the sun sensor.

* Height range adjusts from 3 3/4 inch to 95 mm * Length of pull adjusts from 12 inch to 15 inch, spanning 305mm to 381mm * Printed construction is 100%, no fasteners or glue required * Sling swivels allow for secure hold on your person while not in...

Update This Thing is obsolete, see my improved design here: https://www.thingiverse.com/thing:2905300 This gun controller for the HTC Vive has the following features: Proportions based on the M16, designed for H3VR. Height adjustable stock with 95mm...

If you are using Velcro to mount a Vive Deluxe Audio Strap to your Oculus Quest headset, you can use these rings to fill in the hole a bit and give the Velcro SOMETHING to hold on to besides the narrow edge of the plastic. You do not have to glue...

I have designed a part to attach the filament runout sensor to my Ender 3. ...The sensor holes are aligned straight with the stock extruder. Compatible with the widely available cheap sensor: https://www.aliexpress.com/item/1005001349519472.html

I have designed a part to attach the filament runout sensor to my Ender 3. ...The sensor holes are aligned straight with the stock extruder. Compatible with the widely available cheap sensor: https://www.aliexpress.com/item/1005001349519472.html

This little housing for the light sensor BH1750 on a PCB is designed with simplicity and robustness in mind. The walls are chosen to be 2.6mm thick, and infill should be at 100%. The PCB features a multi-pin connector on its back and two mounting...

26/09/2020 - Update with the new Logo This adapter kit includes : A first file to be attached to the top of the Oculus Rift S using the original helmet mount and with a slot to slide the Vive strap. A second file to be printed twice and then clipped...

Made a custom mount solely for the purpose of using two T nuts to attach the runout sensor directly to the top aluminum 20x20 extrusion. Hardware Needed (aside from the 608 bearings used in the runout sensor): - 2x M3x8mm Button Cap Screws - 2x M3...