mta bus models

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

I have printed all of the parts and assembled a model which is shown. The "Dome" cover will fit over the Base Plate, and in turn a 1/2" piece of sprinkler pipe will fit over the tabs in the center of the Base Plate. The Mic Holder will fit over a Gen...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

To do this I went to https://3dp.rocks/lithophane/ sized it in model settings, and set it to Positive under image settings. I kept it flat since it will be used as the back of the bookstand. But while it's not in use it can also be used as a cool...

I am keenly interested in optimizing this concept so that it Works for those needing a good, quality, multi-purpose coral frag plug so please leave comments on how I might improve this Thing. Instructions Additional fragging tools that might be of...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

The parts I used: 30mm M3 flat screws: https://smile.amazon.com/gp/product/B07NWL5HK3 16mm M3 hex screws: https://smile.amazon.com/gp/product/B014OO5KQG M3 nylon lock nuts: https://smile.amazon.com/gp/product/B07GNXDQJZ 20mm CR-10 springs:...

The diameter is 50mm, 23 teeth, pitch 2, height 20, slop .01.Updated threads were created using Fusion 360 and then incorporated into the Tinkercad models.  Several versions were tested at various tolerances to get just the right fit across...

Any printer that allows for a pause for a filament change will work, but if you use Prusa Slicer you can program in a pause when you slice your model. Much easier.</p><p>Vertically Printed Flags</p><p>The vertically printed versions of the Ukrainian...

Except for the Sunlu mount plate just lay the models flat. The Sunlu mount plate I printed standing upright - even without support (although some minor bridging is needed, but that was no problem)</p><p>As mentioned above, the hygrometers are...

... assemble the mouse similarly to how to disassemble the G305 and use the same screws. (Check). Make sure that everything fits nicely and that all supports are removed. Supports can be deceiving, so check the original model if you need to. ...

This CNC design was born from a YouTube video showcasing a similar project on the cusp of production.\r\nIt's the second CNC machine I've designed, both aiming for an easy-to-build desktop model at an affordable price point.\r\nTo date, it hasn't...

As such, some knowledge of manipulating 3D models will be required in order to make use of these. Since I created them, decided may as well share in case someone else can use them. You can see the principal that allows these masks to work in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 34 printer_tolerance = 0.4...

Please feel free to build on what I've produced, maybe tweak things to find a home for the hero boards or a model of the Batmobile. I'm going to keep my Hot Wheels Batmobile with the hero boards in the Arkham Asylum box. ... ## [CLICK HERE TO...

I did NOT YET test this specific 3D Model, but will do it very soon. I will try to come up with a good default thickness (body_thickness variable). In the meantime you can customize this value right here on thingiverse when clicking on...

On a desktop SLA machine, you can print up to 110 models with 100ml in around 7 hours at 100µm layer height. All parts were printed on a Formlabs Form 2 (SLA) printer at 100um layer height with clear resin. ...Parts were washed with &gt;99vol% IPA on a...

to remove push from the angled face (from the thickest portion) outward and it will release itself from the extrusion.The ideal position is up against the top of the frame, tighten the extruder and make sure your PTFE tube is pushed in all the way,...

All overhangs should be 45 degrees or less. Rafts: Not required, unless you experience adhesion issues. License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is...

The next version will likely have longer front arms, a thinner and shorter middle section, and a removable gimbal mount for storage and travel (for my model of gimbal, Tarot T4-3D, but hopefully can be adapted for others of similar size). Printing...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

Once satisfied with the positioning, the pen can be used more aggressively to fill in the open corners of the shapes, and then along the whole mating edge.Note that the angles at the edges of each frame will not print perfectly, and are not exact in...

When/if I model it, I will put it on here.Have any modification requests? Contact me in the comments. I am active on Thingiverse.If you want to modify the design yourself, I can try to provide the original Tinkercad schematic on request.Update: Added...