▷ mtw create 3d models 【 STLFinder 】

MTW Create Spool Holder
thingiverse

According to the guys at MTW, this should work on both the current MTW Create, as well as the upcoming MTW Create 2 (sorry, but this is not for the Create Express). There are currently a few different versions of the main spool holder, but I would...

BLTouch Mount for MTW Create
thingiverse

Print Settings Printer: MTW Create Rafts: No Supports: No Resolution: 200 micron Infill: 50% Notes: I printed this in PETG because it's close-ish to the hotends and heated bed, but other materials would probably be fine. ...

MTW Create filament spool holder
thingiverse

To install this remove the top caps on the MTW Create and install the left and right bracket using the old M5 screws. I also added a slot nut in the back and used another M5 to attach the lower arm to the back. Print 2 of spacers and 1 center. I...

MTW Create Express Filament Guide Ring
thingiverse

A simple filament ring for my spool holder for the MTW CE. There are two versions, one mounts on the top and one mounts on the side of the tower. You can find the spool holder here: https://www.thingiverse.com/thing:3469789 The flat one goes on...

MTW Create Express Spool Holder
thingiverse

A spool holder to put the filament on the front of the printer. The standalone spool holder that comes with the printer has a bad habit of falling over and it can be hard to see the spool if it's behind the printer. This makes it easily accessible...

MTW DROPSTOCK
cults3d

... of drops. MTW is Mil Spec Buffer Tube strong version MTW to Mil Spec Buffer Tube clean look version MTW is Aeg Buffer Tube The power cord can be interlaced and the Mil Spec versions screw in the screw from the bottom for additional anti-rotation.

MTW Suppressor
thingiverse

It's a suppressor specifically designed for Wolverine Airsoft MTW. Fits inside the m-lok handguard. Hexagonal pattern on the outside. Note that you can't mount anything on the sides, or the lower 45° mlok holes. You want to mount a flashlight etc,...

Create
thingiverse

Sci-Fi create for dioramas. ... 30mm x 30mm x 30mm

Create
cults3d

Sci-Fi create for dioramas. ...30mm x 30mm x 30mm

CREATE
thingiverse

Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockLength = 8 Name = CREATE BlockWidth = 1

CREATE
thingiverse

Customized version of http://www.thingiverse.com/thing:694353 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=694353 Instructions Using the following options: type_your_name = CREATE @ JSU plate_size = 37

Create
thingiverse

Customized version of http://www.thingiverse.com/thing:753477 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=753477

create
thingiverse

Customized version of https://www.thingiverse.com/thing:1038261 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1038261

create
thingiverse

Customized version of https://www.thingiverse.com/thing:4703135 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4703135

create
thingiverse

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 10 hole_radius = 3 stick_thickness = 2 font_thickness = 5 flat_bottom = 2 stick_width = 8 message = CREATE Font = write/orbitron.dxf

Create
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Rotation = 50 Loop_x_position = 10 Loop_y_position = 0 height = [5,6,4.5,5,6,4,5,4,6] Font_name = Anton spacing =...

wolverine mtw barrel clip
thingiverse

for those who have lost or broken your barrel spacer clip on your mtw

Skywing MTW-TD80K Bracket
thingiverse

This is a canister bracket for the MTW-TD80K to fit the Skywing can tunnels, I printed this with 100% infill and ABS

MTW Outer Barrel
cults3d

Hello. ...I prepared 3 models of outer barrels for MTW. Checked with NY 2021 Billet version. ...There is a lenght: 5'', 6'', 7''

Airsoft MTW Suppressor
thingiverse

I recently bought a Wolverine MTW and wanted to have an integrated/nested suppressor in the handguard, but the more I looked the more I had difficulty finding one that would fit AND that I liked. The internal diameter of the MTW's handguard is 35mm.

Wolverine mtw trigger
cults3d

I had one of my triggers break in my mtw and there was no models that I could find that I could 3D print so I decided to model my own it works very well

MTW Forged Dust Cover
thingiverse

I have designed a dust cover to replace the existing dust cover on my MTW forged edition reverse the spring and you now have a dust cover that will properly close

Wolverine MTW Spade Grip
thingiverse

It turns your MTW in to a vehicle mounted pseudo machine gun.:) Adjust the trigger pull length for proper operation. Recommended printing orientations shown above. ------------ Parts list: Stock Mounting plate Upper arc (This has...

QR MTW 1x1
thingiverse