nakka rocketry 3d models

This is a direct translation of the instructions given on [Richard Nakka's website](https://www.nakka-rocketry.net/A-100M.html) for the A-100M rocket motor. Please note: This rocket motor is only for educational purposes when printed in plastic,...

... motor de foguete amador de Richard Nakka. Este é o pequeno e confiável A-100M, um motor de classe G que tem sido usado principalmente para testes de diferentes propelentes à base de açúcar. Source/Fonte: http://www.nakka-rocketry.net/A-100M.html

... foi baseado nas dimensões e blueprints encontrados no site dele. Aproveitem! PS: Se você for usinar este motor, talvez seja necessário fazer ajustes nos sulcos dos O-rings e no bulkhead. Fonte/Source: http://www.nakka-rocketry.net/lambda_p.html

... (AISI 1018), 16 parafusos #6-32 x 1/4" e 2 "O-rings" -129. Este motor comporta o uso de propelente RNX e entrega um total de 455 N-s. de impulso total, bem como 118 s. de impulso específico. Souce/Fonte: http://www.nakka-rocketry.net/epoch.html

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I made this for personal use so feel free to use!

Part Design of 2 Stage rocket

Rocketry tooling. Includes coring / divergent nozzle, convergent nozzle / ram rod, ram rod with hole, ram rod without hole. ... For schedule 40 pvc 1/2"

This is a rocket i found on line here is the link http://www.nakka-rocketry.net/A-100M.html

Long Beach Rocketry Logo designed in AutoCAD

The high power rocket design was created by DG&A Rocketry, a now defunct business. It was modeled using data from RockSim and information on the internet. ... It was converted to dual deploy and has room on the end for a engine retainer.

This is a simple rocketry launch controller designed to accommodate an XT30 connector as the safety switch, an Illuminated Toggle Switch with Cover (guard) from Adafruit, and an Illuminated Triangle Pushbutton also from Adafruit. This launch...

Model made for use with Estes Model rocketry partsyou need 2 centering rings

The rocket is designed to allow for flow streaming through the craft and being accellerated, or even ionized during the period inside the rocket, that could bring pressurized gas to feed the propellers at higher altitudes then we can to this day with...

not finished

Spiral rocket fins for model rocketry. Use standard 18mm motors like C6 dor D9 motors. ... Need a 40mm cardboard tube.

The design was not originally intended to be 3D printed but can be with scaling modifications of the parts. If you would like to learn more about our team and the rocket itself you should check out our website, https://rocketry.ncssm.edu/ Category:...

Hello, this is BRRDS, (Best Rocketry Research Determination System), a high-power rocket developed at NCSSM over the past 3 years from 2019 and launched in late 2021. The purpose of the rocket was for research but really being able to go...

Hello, this is BRRDS, (Best Rocketry Research Determination System), a high-power rocket developed at NCSSM over the past 3 years from 2019 and launched in late 2021. The purpose of the rocket was for research but really being able to go supersonic...

Hello, this is BRRDS, (Best Rocketry Research Determination System), a high-power rocket developed at NCSSM over the past 3 years from 2019 and launched in late 2021. The purpose of the rocket was for research but really being able to go supersonic...

My first revision of an experimental flight avionics board for 54mm model rocketry. Pretty tough to design though. This device consists of three PCBs stacking together. The power management board(bottom) contains a switching regulator from TI and two...

It is the logo of the National Association of Rocketry. www.nar.org they gave me permission to post it here. The picture of is Logo 2 - Logo 1 is the inverse. Licensing is as listed with two more conditions. No usage that will harm the NAR and no...

The SS-5 datasheet says the switches are rated for 100G of shock loading, and I would personally only recommend using these switches with rocketry electronics that utilize a brownout capacitor, just in case there are any extreme G-load events...

These models are the result of a study of the Von Kármán spline for creating aerodynamic nose cones for model rocketry. There are various models that all use the same shape. The nose cones are 15.6 cm in length with a 5.4 cm diameter. The nose cones...

A100M Rocket Engine I used the plan from Richard NAKKA's work to modelized this engine on SolidEdge ST9.You can check a complete description of this model with the link below :https://www.nakka-rocketry.net/A-100M.html#Basic

Used on many of my rockets. Currently 1g, 2g, 3g, 4g, 6g, 8g, and 12 g tube. Sizes are calibrated assuming 1g of FFFFg = approximately 1 cc. The bottom takes a #4 or M3 screw to hold it to the bulk plate. The hole at 45 degrees is for the wire to...

This is a ruler for drawing straight lines on tubes that are parallel to the centre of the tube, useful for marking fin locations on model rocket bodies. As a reminder that in model (and larger!) rockets the centre of pressure should be behind the...

Two OpenSCAD files for generating fin alignment jigs (one for three-finned rockets and one for four-finned rockets). Set the parameters at the start of the file and the rest should be pretty automatic. ...Please contact me with any questions or...

These are a set of tools for building model rockets. They help to cut body tubes, position fins and launch lugs and marking body tubes evenly. For these to work best, they need to fit on the body tube snugly so your printer needs to be well...