neo geo case raspberry pi 3 3d models

This would be at the end, a thermal camera, with an mlx90640 sensor on the front and a raspberry pi + 3.5inches screen in the back, on a dual 18650 accu grip holder. Models to be uploaded one by one.. Here is the raspberry pi case. The...

This would be at the end, a thermal camera, with an mlx90640 sensor on the front and a raspberry pi + 3.5inches screen in the back, on a dual 18650 accu grip holder. Models to be uploaded one by one.. Here is the raspberry pi case. The particularity...

Summary Case for Raspberry Pi 3 (2 or B+). The imported rPi SVG logo comes from Wikipedia: http://en.wikipedia.org/wiki/File:Raspberry_Pi_Lo... update_1: I changed the lower_part.stl by removing chamfers on bottom part holes, making it easier to...

Designed to house the pi 3 with an option for a 30mm fan mounted in the top dome, this enclosure is a must-have for any Raspberry Pi enthusiast. With ease of printing in mind, the case is sectioned into four parts. Ten M3 x 15mm screws are...

This is a practical solution, well-suited to a Raspberry Pi 3 combined with a NAVIO 2 board. For installation, you can choose between using the 50mm x 58mm mounting holes of the Raspberry or the 35mm x 35mm pattern found on the underside of the case....

This is my innovative enclosure concept for a Raspberry Pi 3. ...A robust 45 x 45mm fan provides superior airflow and efficient cooling capabilities.

The lower section of the 0110-M-P's Raspberry Pi 3 enclosure has been customized to accommodate 2020 extrusion profiles and comparable systems.

I present the Pi 3 NES cart case, a simple holder that cradles your favorite NES cartridge with a Raspberry Pi 3 cleverly installed within. For those who are creative and ambitious, there's room to install a hard drive, along with a convenient hole...

I was determined to position my Raspberry Pi 2 right next to the Mini-USB Port on my Ender 3 printer and utilize my existing case. Therefore, I designed a custom holder for the case that can be securely fastened to the 4040 rails using screws. In...

Raspberry Pi 3 case in a cute retro look package. This stylish design by McNugget is intended to be laser-cut, but I adapted it for 3D printing. Your results may vary. FROM McNugget's instructions: Please insert the back plate first and then use...

To assemble the case, follow this order: (1) Install the fan, (2) push the power supply wire through the rear port, (3) attach the fan and power wire pins before inserting the Pi, (4) start the two #4 screws into the Pi, (5) carefully insert the Pi...

 This is the Playstation Pi Tiny V.3, it is an improved version of the V.2, this version is edited so it will be easier to print, easier to put together, and overall touch-up, for better look.This model might not be compatible with the V.1 and...

My case model looks like this:...

Adaptation of @Superrei's groundbreaking Raspberry Pi Zero case tailored specifically for a Raspberry Pi 3A+. The original design, renowned for its innovative hinged structure, is now perfectly compatible with the new model, still print-ready in one...

The subject of our discussion is my custom-made Raspberry Pi case. It is based on the design provided in a specific file: Raspberry Pi Model B+. ...For inventors, the file contains various models; however, we are particularly interested in the...

Raspberry pi zero case used with my ender 3 implementing octoprint. I know octoprint folks don't like to see the zero W used here but it works fine without the camera. I use an independent wifi camera instead. I rehashed SvenRau and cfunseth's things...

The Raspberry Pi fastens to four points on the second layer of the case using counter sunk bolts through holes in the first layer. You'll need four small 3mm bolts to attach the Pi to the case and another four 3mm bolts for the corners. Yes, the Pi...

Simple Media Center Case for the Raspberry Pi 3 without visible screws on top. The cover is screwed through the bottom so you may need rubber pads on the bottom if you don't use countersunk screws. Inside the case, there's additional space for a USB...

This Raspberry Pi case is specifically designed for the pi 2 and 3 models, mimicking the look of the original Playstation 1 console. The intention behind this design is to be used as a base for emulating old games on ReTroPie, but it can also serve...

The Raspberry Pi 3 and 2 Case Design Focuses on Simplicity. One end of the board fits snugly into the case, and a friction cover tightly closes it while still leaving space to access the SD card. To print the case standing upright, you don't need...

Since the Ender 3 V2 doesn't really have any extra space to integrate accessories/mods and I didn't want to give up the drawer, I made this Raspberry Pi case that can be mounted underneath the built-in drawer. It requires the raised feet to be added...

I took Holspeed's Ender 3 Tray and integrated a raspberry case to house your OctoPi, adding a crucial hole in the back for an XT60 connector. Next, I utilized an XT60 splitter to tap into the printer's power source, stepping down 24V to a reliable 5V...

I'm absolutely enamored with the sleek design and striking appearance of the HP OMEN Accelerator, which prompted me to create a custom case for my trusty Raspberry Pi 3 Model B. UPDATE# 03/19/2020 The STL files for this design are no longer...

Raspberry Pi 3 Case Takes Shape Like Classic PlayStation Console, with Hinge for Easy Access. Plenty of Room for Fan Inside, All Ports Remain Visible. Low-Resolution Preview Serves as Proof of Concept. Designers Opted for Q-Tip Shaft as Secure Hinge...

This custom case is built specifically for the Raspberry Pi 3 and its B+ variant, offering users a direct connection to all available ports and pins on these devices. The design also features a snap-fit construction, making it effortless to...

Wall mountable case for Raspberry Pi 3(B/B+). ...I needed a way to secure my enclosure and have power directly soldered onto the GPIO pins.\n\nParts:\n3 M3 Nuts\n3 M3 8mm Bolts (Lid)\n4 M3 6mm Bolts (Case)\n1 2.1 MM 5A DC Power Jack Socket Threaded...

A Raspberry Pi 2/3 Stackable Cluster Case. These base pieces are compatible with my Orange Pi Zero Cluster Case (https://www.thingiverse.com/thing:2994496) and can be stacked together seamlessly. Note that it is not compatible with my orange pi one...

This is a 40mm fan case for Raspberry Pi 2/3, based on the GREAT mount case from giacomo30196. I have removed every gpio/camera holes and centered the 40mm fan mount and a small hole for my oled gpio cables. I added a simple optional oled pocket...

Raspberry Pi case for 3030 profile with OCTOprint logo on the bottom. Add filament change on the 6th layer for a colored logo. ... This is a remix from https://www.thingiverse.com/thing:398515

Case for the Raspberry Pi 3B+ with Power over Ethernet HAT: - A cutout is provided on the side of the upper part for the fan and ventilation slots. ...- The underside features an adaptation that enables screwless fixation of the board.